Boom BC, as shown, supports a load of 10 kN which is then mainly supported by cable AB. The boom used is a C150 x 19.3 steel section with the following properties:A = 1990 mm?ly = 6.29 x 106 mm4x(bar) = 12.7 mmrx = 56.4 mmly = 0.358 x 106 mm4Ty = 13.4 mmTYPICAL SECTION:10 kN20 kNx{bar)4 mWhich of the following most nearly gives the axial force in the boom?Select the correct response:38.14 kNO 25.42 kNO 33.24 kN29.63 kN

The given load on the boom is 10 KN.

Boom BC, as shown, supports a load of 10 kN which is then mainly supported by cable AB. The boom used is a C150 x 19.3 steel section with the following properties: A = 1990 mm? = 6.29 x 106 mm4 ,= 0.358 x 106 mm4 x(bar) = 12.7 mm Tx = 56.4 mm Ty = 13.4 mm TYPICAL SECTION: 10 kN 20 kN x(bar) Which of the following most nearly gives the axial force in the boom? Select the correct response: 38.14 kN 25.42 kN 33.24 kN 29.63 kN

Boom BC, as shown, supports a load of 10 kN which is then mainly supported by cable AB. The boom used is a C150 x 19.3 steel section with the following properties: A = 1990 mm? = 6.29 x 106 mm4 ,= 0.358 x 106 mm4 x(bar) = 12.7 mm Tx = 56.4 mm Ty = 13.4 mm TYPICAL SECTION: 10 kN 20 kN x(bar) Which of the following most nearly gives the axial force in the boom? Select the correct response: 38.14 kN 25.42 kN 33.24 kN 29.63 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Chapter Three FUNDAMENTAL PROBLEMS All problem solutions must include an FBD. FE pl F3-1. The crate has a weight of 550 lb. Determine the force in each supporting cable. F3-1 -2. The beam has a weight of 700 lb. Determine the hortest cable ABC that can be used to lift it if the naximum force the cable can sustain is 1500 lb.
8) A shaft of diameter (d = 5-mm) is to be puled through a (4.5)-cm-diameter glycerin-filled sleeve as shown in Figure. The glycerin to be used has a dynamic viscosity of 1.5 Pa.s, and the cable is pulled by 60-N tensile farce. If the cable is to be pulied at a velocity of 0.02 m/s and the velocity profile equation though glycerin is (u = 0.6y + 20y), what is the length of the sleeve that can be used to provide this velocity? Assume that the cable can be kept at the center of the sleeve. Seve Shaft
A flexible cable is subjected to a uniformly varying load.If the tension at the supports is 12 kN, what is the valueof the sag “h”? SHOW COMPLETE FBD
1
complete clear solution, please, thank you!
Note: Hi, pls need help. Any solutions are highly appreciated. I will rate this right away. Thank you in advance! what is the maximum moment about minor axis in N-m? Considering sag rods and tie rods at midspan (2 decimal places) A 20m Fink Truss are spaced at 'S' meters o.c. the purlins are made up of C10X20 sections and are spaced 1.1967m on centers. The truss has a height of 4m. Roof LL is 'RLL' N/m2 of roof surface and roof covering is assumed to be 'RDL' N/m2 of roof surface. Determine whether the purlins are adequate to carry such loadings. Fy = 248 MPa. C10X20 properties: w=29.76kg/m, A=3787.09mm2, Ix=32.84x106mm4, Iy=1.17x106mm4, Zx=317.91x103mm3, Sx=258.92x103mm3, Zy=44.25x103mm3, Sy=21.47x103mm3 S (m) RLL (N/m^2) RDL (N/m^2) 6.00 900 900
Show the complete solution.
If x = 2 ft and the crate weighs 300 lb, which cable segment AB, BC, or CD has the greatest tension? What is this force and what is the sag yB?