Block A has a mass of 100 kg and the coefficient of friction is 0.20. Determine the friction force between A and B. 500 N 90° A 30° 450 N B

Q: LQ.5: Calculate the force in member GC "Fgc = 24 kN " Tension O %3D %3D "Fgc 27 kN "Tension O %3D…

A: Given that:

Q: Concrete Hollow Block 200mm H x 400mm Lx 150mm thick per piece and Laying 4 layers x 4 meters…

A: "Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Handwritten/ neat work pls show the steps on how u got the areas and not just the answers. Parts d,…

A: A framing plan is given we need to find out the tributory areas

Q: What is the Liquid requirement rate in perforated plate scrubbers?

A: The liquid requirement rate or Liquid to gas ratio is the volume of liquid injected per volume of…

Q: Provide clear and step by step solution Using ASD, check the adequacy of the base plate…

A: ASD: ASD means Allowable stress design. It is also known as Allowable stress design. In these…

Q: Q10: The following values were found from the corrected load versus penetration curve Satisfactory…

A:

Q: What are the Shear-Flow Resultants?

A: There is a wide variation in shear flow in the open sections and closed cross sections. In case of…

Q: Weight Retained 1.570 kg 1.554 kg 2.570 kg 1.84 kg 2.223 kg 0.22 kg 0.023 kg Sieve No. Cum. Weight…

A:

Q: Q1 Define five of the following with sketch compulsory. ( 1-Allotropy 2-BCC 3-yeild strength 5-…

A:

Q: Define the following a(Point of contra flexure b) Section modulus

A:

Q: Define Total Stress Method.

A: The total vertical stress method is defined as method which is used for determining the stress…

Q: Explain why piezocone test (CPTU) is used ?

A: Cone Penetration Test Cone penetration testing (CPT) is an in-situ test is used to  identify the…

Q: answer with short

A: The solder was disturbed while cooling, or has overheated in operation to the paste phase and so…

Q: Briefly describe Mix Columns

A: To describe Mix columns

Q: Give the purpose of having Sieve analysis of Aggregates

A: A sieve analysis determines the distribution of aggregate particles by size within a given sample.…

Q: Find the centroid of given composite figure. Set- up the reference axis on the lower left corner.…

A: Centroid about x-coordinate :x¯=A1x1+A2x2+A3x3A1+A2+A3

Q: There are many different types of ALM environments, but here are a few to get you started:

A:

Q: theory of discussion determination of shrinkage lim

A: Solution: The Shrinkage limit is generally used in the classification of soil that is in…

Q: what is the aci design mix or proportioning of standard compressive ddesign strength values (without…

A: The American Concrete Institute (ACI) mix design method is but one of many basic concrete mix design…

Q: Define the minimum weight of fine aggregate for sieve analysis as per ASTM C136 ?

A: ASTM C136, 2006 Edition, February 15,2006 - Standard Test Method for sieve analysis of Fine and…

Q: How did you determine its a smooth pipe?

A: Given data: εd=9.87×10-5Nd=944,444.44

Q: Mohr's circle is shown for a point in a physical object that is subjected to plane stress. Each grid…

A:

Q: Situation 21: A square tied column carries a factored load of 2800KN. It will be designed using…

A: Columns are structural members which carry compression loads transferred from the beams and slabs.…

Q: the load is 150kN at the center of the beam and the dimension of the beam is 6x6x24. compute for…

A: P=150kN L=24 b=6 h=6

Q: Prepare a complete NC program for finishing profile shown in fig.2 with continuous cut in clockwise…

A:

Q: epare a datasheet and calculate the cost of plastering cement (1:5), 20mm thick for 50m². Also…

A: Given data:- Ratio of plastering cement is 1:5 Thickness of plaster is 20 mm Area of plastering is…

Q: * Standard Reference of Atterberg Limits Test is ASTM D 8215 O ASTM D 4318 O ASTM D 6523 O ASTM D…

A: The ASTM D 4318 gives the standard test procedures for determination of liquid, plastic and…

Q: : Prtal methed

A:

Q: Differentiate between the following:                         Q) Two way beam supported Slab & Flat…

A: Slab- It is defined as a horizontal structural member of reinforced cement concrete used to support…

Q: Make a tabulated Data .  Brand A ( pozzolan Mabuhay Brand - make a remarks either Good condition or…

A: Solution: The Republic cement Provides high quality products of cement that are very consistent for…

Q: sieve analysis what's the meaning or gonna happen if the So is zero

A: A sieve test is generally called as gradation test, is one of the most important and widely used…

Q: What is the main working member of a grader? Oa. Moldboard O6.0perator Oc. Large tires. Oa.Engine

A: Grader is a heavy machine which used in the road construction .

Q: dure of using depth dial gauge to measure the depth of corrosion. Concise and clear.

A: A depth gauge typical refers to is a precision measurement instrument that is used by mechanical…

Q: A sieve analysis test was performed on a sample of coarse aggregate and pro- duced the results in…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: Differentiate porosity, permeabiloity, water saturation and resistivity properties. What…

A: Solution: Porosity: It is defined as the property of loose sediments, rocks, or soil to hold fluid…

Q: Discuss Allowable Stress Design

A: MAIN CONCEPT OF DESIGN: load<resistance ALLOWABLE STRESS DESIGN is one of the design concept. In…

Q: Define Vane Shear Test (VST)

A: In soil mechanics, the properties of the soil are used for a lot of calculations, Some of the…

Q: b. Shrinkage is defined as the reduction in volume of 1.2 Fill the blank space (s) with the correct…

A:

Q: Describe about the Flat-blade dilatometer testing.

A: The Flat Dilatometer Test:

Types of Cement

Cement is a fine mixture of limestone, chalk, or marl and clay which when mixed with water, becomes compacted due to the formation of strong molecular bonds. Due to hydration, cement turns into a hard mass when left for a sufficient amount of time upon mixing with water. The water turns the cement compounds into gel-like submicroscopic particles having higher surface areas. It is due to the hydration properties of cement, they are often known as hydraulic cement. For instance, Portland cement is a popular example in this category.