B- In the Venturi scale, kerosene flows at a density of 0.82 kg/ m3. If the choke diameter is 10 cm and the input diameter is 20 cm, the decrease in pressure between the two points is 30,000 pascal. Calculate the speeds of the kerosene flow. 3 Mark

Q: width and 5 m A horizontal square wooden rod, 2 m long. 0.2 m head width is hung and fixed at the…

A:

Q: Pressure in the inner tube of a bike tire is 118 psi. Change this pressure to atm. O A. 8.03 atm B.…

A: Answer: A. 8.03 atm

Q: Water flows in a pipeline composed of 75 mm and 150 mm pipe. Calculate the mean velocity in the 75…

A:

Q: While attempting to extinguish a fire, firefighters are holding a nozzle at the end of a hose. If…

A:

Q: Q2 // The diameter of a pipe at section 1 and 2 are 10 cm and 15 cm respectively. Given velocity of…

A: Given that, The diameter of the pipe at section 1 D1 = 10 cm = 0.1 m The diameter of the pipe at…

Q: 5. A Pitot tube in the pipe in which air is flowing is connected to a manometer containing water as…

A: Given that- Manometer difference in water level, x=87.5 mm= 0.0875m Tube coefficient, CP=0.90…

Q: 1-Water with kinetic viscosity v-0.494 mm2/s flow through a pipe with diameter 18mm with velocity…

A: Kinetic viscosity = 0.494 mm2 /sdiameter = 18 mm V= 0.1 m/sf  = 0.03 mm

Q: A solid cylinder of weight 9 kg slides in a vertical lubricated pipe. The clearance between the…

A:

Q: Estimate the friction factor for a flow with a Reynolds Number of 1,203. Enter your answer in…

A: Friction factor for flow having Reynolds no. 1203 needs to be calculated.

Q: 3-foot-long, 8-inch-diameter cylinder inside a 25.8-inch-diameter tube at 3 feet per second. Fluid…

A: Given data: Length of pipe= 3ft Kinematic viscosity=0.006 ft2/s Constant velocity=3fps  Relative…

Q: Determine diameter of galvanized pipe needed to make the water flow along 180m with flow rate 85L/s…

A: Given data: Length of pipe = 180 m Volumetric flow rate = 85 L/s Head loss = 9 m Kinematic viscosity…

Q: An oil (S = 0.85, v = 1.8×105 m²/s) flows through 0.1m diameter pipe at 2m³/sec, 150m long. Find the…

A:

Q: Q: An open cylindrical vessel of (20 cm) diameter and (100 cm) long contains water up to a height of…

A: Given diameter of open cylindrical vessel of =20 cm length of open cylindrical vessel of =100 cm…

Q: The velocity profile of a fluid in a horizontal circular pipe having a radius R is found as; Vz =0.4…

A: Given data: Velocity profile for a fluid in a circular horizontal pipe is given by the following…

Q: There is a drop in the bubble with the diameter of 10mm and pressure of 250 KN/m?. If the surface…

A: In fluid mechanics, surface tension is defined as the property of the surface of a liquid allows it…

Q: Brine (SG = 1.1) is flowing through a 100-mm ID smooth pipe at a Reynolds number of 48000. The…

A:

Q: This factor is usually neglected on calculation for pressure drop. A Acceleration B Elevation…

A: Pressure Drop: Difference of total pressure between two point in a fluid flow network is called…

Q: A nozzle is bolted onto a pipe by the flanged joint as shown in the Agure. The flowing fluid is…

A:

Q: 8. Oil flows in the pipe shown in figure. The orifice in the pipe has a coefficient of discharge of…

A: The orifice meter is a flow measuring device. The difference in pressure gives the flow rate of the…

Q: A smooth pipe has an inside diameter of 28 mm, is 16 m long, and carries 10C water at a rate of 8…

A: Given,The diameter of the pipe is, the length of the pipe is, the temperature of the water is, The…

Q: Determine the pressure drop across the orifice meter as shown in Example Figure

A: Given,  ρ1 = 1000 kg/m3 d=0.022 m ρf=1100 kg/m3

Q: Unit for mass flow rate and molar flow rate

A: The mass flow rate is defined as the differential mass of the fluid flowing per unit of time. The…

Q: A straight pipe with an expansion in pipe from 6 to 11 cm transports water at a rate of 0.011 m /s.…

A:

Q: Paddle agitator

A:

Q: Calculate the cross-sectional mean velocity of water flow in a pipe. The pipe diameter is 5.0 mm,…

A:

Q: 5.1-2. Frictional Pressure Drop in a Flow of Olive Oil. Calculate the frictional pressure drop in…

A: Olive oil density and viscosity at a given temperature are obtained. The Reynolds number is…

Q: In the Figure.Q3, The energy decline of the connections and the pipe before the pump is 3m.…

A:

Q: As a chemical engineer you need to pump the products without affecting products properties. Because…

A: Since you have posted a question with multiple subparts, we will solve the first three subparts for…

Q: Q4: a) Determine the valve lift & valve dimensions of an engine from the following data: Bore 140…

A: To determine the valve lift and valve dimensions of an engine, we need to use the provided data and…

Q: The U tube shown is rotated about the left vertical leg at 30 rpm. The pressure at point A is…

A:

Q: Criticize why this situation happens.

A:

Q: 1. An incompressible fluid of kinematic viscosity v= p/p = 10-4 m²/s flows steadily through a…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: calculate the largest discharge for which the flow will be definitely laminar Water flows in a 2 cm…

A: This question is based on fluid mechanics. The flow in consideration is Laminar flow. Data given :…

Q: For the configuration shown in Figure 1, calculate the weight of the piston if the gage pressure…

A:

Q: Sulphuric acid is flowing through a pipe (2.5 inch diameter, 50 ft length) in a velocity of 0.006 m3…

A: Given: diameter D = 2.5 inch = 0.0635 m, A = pi.D2/4 = 0.003165 m2 Thus, V = Q/A = 0.006/0.003165  =…

Q: As shown in the figure, the manometer reading is 15 cm of mercury when the tank is empty (water…

A:

Q: An oil is used to lubricate a thin plate with a surface area of 5.382 ft? that is placed between two…

A: Given that, The surface area of the thin plate A = 5.382 ft2 = 0.5 m2 The distance between the two…

Q: Assume that the 5-in. valve with Cvmax = 500 is selected and that the pressures around the valve are…

A: The flow rate considered for the valve is gallons per minute. The rangeability parameter represents…

Q: Derive from the first principles the steady flow energy equation for a turbine taking into account…

A: To derive from first principles Steady flow energy equation for a turbine taking into account that…