(b) Design an interfacing circuit for the microprocessor system by using the following components to meet the specifications listed in Table 4. Complete the wiring at the 8085 microprocessor memory map system in Figure 4.1 that interfaces with the memory components and tabulate the possible address range of each memory chip. You can use a 74LS138 decoder or any related gate logic. [Rekabentukkan satu litar pengantaramukaan untuk sistem mikropemproses yang menggunakan komponen-komponen berikut untuk memenuhi spesifikasi disenaraikan dalam Jadual 4. Sempurnakan sambungan pada sistem peta ingatan mikropemproses 8085 dalam Rajah 4.1 yang menghubungkan komponen-komponen ingatan dan jadualkan julat alamat yang mungkin bagi setiap komponen ingatan. Kamu boleh menggunaan penyahkod 74LS138 atau get logik yang berkaitan.] Device ROM A (2716) RAMA (6116) RAM B (6116) RAM C (6116) ROM B (2716) Table 4.1 [Jadual 4.1] Specification Address begin at 0000H Address begin at 3000H Address begin at 5000H Address begin at 7000H Address begin at 9000H

(b) Design an interfacing circuit for the microprocessor system by using the following components to meet the specifications listed in Table 4. Complete the wiring at the 8085 microprocessor memory map system in Figure 4.1 that interfaces with the memory components and tabulate the possible address range of each memory chip. You can use a 74LS138 decoder or any related gate logic. [Rekabentukkan satu litar pengantaramukaan untuk sistem mikropemproses yang menggunakan komponen-komponen berikut untuk memenuhi spesifikasi disenaraikan dalam Jadual 4. Sempurnakan sambungan pada sistem peta ingatan mikropemproses 8085 dalam Rajah 4.1 yang menghubungkan komponen-komponen ingatan dan jadualkan julat alamat yang mungkin bagi setiap komponen ingatan. Kamu boleh menggunaan penyahkod 74LS138 atau get logik yang berkaitan.] Device ROM A (2716) RAMA (6116) RAM B (6116) RAM C (6116) ROM B (2716) Table 4.1 [Jadual 4.1] Specification Address begin at 0000H Address begin at 3000H Address begin at 5000H Address begin at 7000H Address begin at 9000H

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Please see image and solve part B only
3. Draw the block diagram of a 16Gx64- ICs, bit RAM using 8G×32-bit RAM R/W external Use minimal number of components. Each RAMI IC has R/W, CLOCK, EN', Data (DO-Dm), and Address (AO-An) pins. Block diagram of the RAM IC is shown in Figure 2. You IC block gates, and decoders. CLOCK DO-Dm EN 8Gx32-bit RAM may use a gener ic decoder AO-An diagram in your solution. A Figure 2. Block diagram of a 8Gx32-bit RAM IC.
Create the opcode table for the ALU by giving a binary code and a name for each instruction you built in Logisim in phase one.
4. Explain the register transfer instructions along with their timing signals required during the fetch and decode phase of an instruction using the common bus structure. Also derive the logic gates and draw the bus structure required for these RTs.
Categorize and Analyze MIPS ISA representing instructions format. Include MIPS Assembly examples in your answers for each type.
The system writes to VA page 30 if an instruction is not accepted; what does it mean? Compared to a TLB handled by hardware, a TLB controlled by software would be quicker in the following cases:
Draw the complete design for constructing a SRAM memory of a total capacity 512KX32 using a SRAM memory 256KX8.
Differentiate between the 8051 Microcontroller's short and long jumps. Using an 8052 microcontroller programme, describe five conditional jump instructions in detail. The embedded system is the subject of this paper.
It is usual to use both row and address decoders to access each memory location in the DRAM of a practical memory system. A 256Mx1bit DRAM chip design is limited to using decoders with 13 address inputs. (b) OW What is the minimum number of banks of DRAM required in this chip? (i) (ii) How many AND gates are saved in this design compared to that using a single decoder? Ignore any multiplexers required in the design. (iii) Sketch the logic needed to select between the various banks of DRAM. Represent each bank of DRAM as a 'black box' with appropriate input and output signals.
A large endian byte addressed memory system with eight distinct memory modules is included in a computer system. Each memory module has 134217728 cells and is 32 bits wide. a) What is the 32-bit memory address of cell 1048578 in module 3 if the memory uses high order interleaving? b) What is the 32-bit memory address of byte 1048575 inside module 2 if the memory uses high order interleaving? c) What is the 32-bit memory address of cell 511 inside module 1 if the high order interleaved memory utilises little endian storage order instead of big endian storage order?
Explain Direct Memory Access (DMA) and input/ output timming diagram with clock synchronization.
When a datapath was implemented, it only allowed for the register addressing mode. Which link in the data pipeline is unnecessary here?