b) An input voltage source Vs of 130mV RMS and an internal resistance Rs of 100is connected to an amplifier that has an input impedance of 3.3kN, a voltagegain of 150 and an output impedance of 220N. The output of the amplifier isconnected to a speaker that has a load resistance of 2.7kN.Determine the output voltage across the speaker.Calculate the effective voltage gain.(s)ks)ks)i.ii. Explain how the effective gain can be increased.

Answered: Image /qna-images/answer/d1ddf025-598e-442a-861a-3b6527aac571.jpg

b) An input voltage source Vs of 130mV RMS and an internal resistance Rs of 100 is connected to an amplifier that has an input impedance of 3.3kN, a voltage gain of 150 and an output impedance of 2202. The output of the amplifier is connected to a speaker that has a load resistance of 2.7kn. Determine the output voltage across the speaker. Calculate the effective voltage gain. i. ii. iii. Explain how the effective gain can be increased.

b) An input voltage source Vs of 130mV RMS and an internal resistance Rs of 100 is connected to an amplifier that has an input impedance of 3.3kN, a voltage gain of 150 and an output impedance of 2202. The output of the amplifier is connected to a speaker that has a load resistance of 2.7kn. Determine the output voltage across the speaker. Calculate the effective voltage gain. i. ii. iii. Explain how the effective gain can be increased.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Calculate the input impedance for small-signal equivalent circuit. Circuit Parameters / R1=9 k2, R2=13 kn, =20 kn Vcc R1 WナKa R2 Rin a. 26.162 ko O b. 16.879 kn O c. 10.971 kn O d. 22.786 ko O e. 29.538 kn
COMMON EMITTER AMPLIFIER CIRCUIT Choose appropriate parameters for the CE amplifier circuit (shown in figure) with a sinusoidal input of amplitude equal to 6mV and a gain of 1.9. Find Vout Choose appropriate parameters and solve the above question.
For the BJT circuit shown below, sketch the hybrid equivalent model circuit with labels of voltages, impedances, and currents. ... 1.8k0 Vo 39ka 22ko tuF-POL 10UF-POL 1200 1uF-POL 2N2221 100mv 1.5KHZ ODeg
QUESTION 1o For the amplifier circuit below given Kp 2.4mA/V essume A0, Vip1.5V. Q point(1.7mA, 3.JV), VDC-10V, R135OK ohm, l2-242K ohm, R 3SKohm, R sig 2kohm Determine the value of gin ms Signal Source
VoD +12 V For the circuit of the adjacent figure a) Given that Ip = 2.83 mA, VGS(om=-7 V and Ipss = 8 mA , find VDs and VGs.. b) If a 50 mV rms input signal is applied to the amplifier, what is the peak-to-peak output voltage? gm = 5000 µS. c) Calculate the output resistance. %3D Ro 10AF 0.1 uF R 10 L. Ra 10 MA 10kn ID= 2.83 mA, Vas (Oef)=-7V. %3D
Find the desired in point 54 with finding what you can find.
A. Given Vcc= 10V, VEE=-10V, IEE = 1 mA, Rc = 10 kW, VBEon = 0.7V. Determine IC1, VCE1 and VCE2 for the following common mode inputs: 1. Vcm = 0V 2. Vcm = 5V 3. Vcm = -5V B. Analyze what is happening to the VCE for the different common mode voltages. You may relate it to the supplies.
4) Below is the small signal model of a multistage amplifier. Using this model, write the equationsthat you would need to determine the voltagegain. IMPORTANT: You only need to providethe equations that you would need to determinethe voltage gain. You DO NOT need to combine and simplify the equationsto determine a final expression for the voltagegain. Vin Vo Vb vo1 Rb R13 Vbe1 Vbe2 'e gm 1 Vbe1 gm 2 Vbe2 Rc2 Rc1 Re