angent grades of +2 on of 152 m above th th of the passing sig of the curve. (c) Co

Q: Explain grid leveling.

A: LevelingLeveling is the method or procedure to determine the relative altitude of any point on the…

Q: Which one of the following is the most economical store design? a. Geometrical layout b. Angular…

A: the correct answer is option c - straight floor layout

Q: Define Land Drainage.

A: Drainage is a reverse method of irrigation  This is generally known as the removal / disposal of…

Q: Explain the step-by-step process of the methodology for lot area sketch plan preparation. Give…

A: The lot area sketch plan A lot area sketch plan is a rough drawing that shows the layout of a piece…

Q: draw any plan using 3x1.5x2.4m

A:

Q: Define earth work

A: The engineering work that is created by moving and/or processing unformed rock or large amounts of…

Q: Design a typical layout model for a Water Supply Scheme

A: Brief Concept- Water Supply Scheme- It is the set up of different units for the treatment of water…

Q: In detail what is the CSI MasterFormat and what is listed in division 28?

A: Answer  CSI MasterFormat also known as "Dewey Decimal system" is the product of the Construction…

Q: 32. What is the area of an octagon inscribed in a circle having an area of 224 sq.m?

A:

Q: Differentiate between BIM and 3DModeling?

A:

Q: 17. COMPLETE THE FOLLOWING INSERT CODE IN INCHES: MG 43 18. COMPLETE THE FOLLOWING INSERT CODE IN…

A: 17. It is made up of  CNMG432       1/2" inner circle , 1/32" corner circle and 80°  Diamond woth 0°…

Q: Write the units used by English systems to specify small areas?

A: Solution: In the English system, areas are basically given in square feet or square yards. For…

Q: Give a brief description: a. Measurement of Horizontal Distances b. Omitted Measurements c.…

A: Any plane which contains horizontal line and perpendicular  to the vertical direction is called as…

Q: Compute total indeterminacy

A: Given data : Number of external support reaction (R)=2+2+2=6 Number of member attach at hinge joint…

Q: Q#9: Explain different methods of Plane Tabling.

A: There are four methods to perform plane table surveying. a) Radiation - 1)It is the method of…

Q: List the different meridians are used to specify directions?

A: The direction of a survey line can be defined in two ways: Relative to each other  Relative to some…

Q: Define two-way flat plate.

A: Solution: A flat plate is generally a two-way system that is supported directly on columns or…

Q: derivation of the formulas used in every section

A: This question has been taken from fluid mechanics

Q: Define Borings Spacing and Depth.

A: Borings should be placed at intervals not exceeding 100 feet and at the ends inside the existing…

Q: Write information about SLP systematic layout planning in design warehouse?

A: Systematic Layout Planning (SLP) can be understood as a tool which is mainly used for arranging the…

Q: 3 75 15 7 10 SECTION A-A VIEW B-B 00

A: We have to asked type of line being of pointed by the leaders.

Q: What is the most important thing to ensure when it comes to layouting?

A: Civil surveying is a type of engineering that includes analysing and documenting information about a…

Q: what is the usual drawing paper size in preparing a lot plan ?

A: The drawing sizes for the construction plans will come in the different formats — with 18” x 24” and…

Q: Define Horizontal Drainage.

A: Horizontal drainage is a helpful strategy for consolidating soils which are weakened by water…

Q: ow many square yards are there in a 72” x 112 yard roll?

A: GIVEN  WIDTH = 72"   = (72" )* (1'/12")*(1 yard/ 3') = 2 yard Length = 112 yard

Q: Give a detailed explanation and steps of the methodology of lot area sketch plan preparation.

A: The methodology for preparing a lot area sketch plan typically includes the following steps:…

Q: Q25. Draw the plan, section and elevation of the given line diagram. BАTH 2000 x 2500 BED 5000 x…

A:

Q: What size will it be if 4" is at scale 2"=1"

A: Given tha scale  2"=1" Thus defines the sclae ratio  for a drawing is 2:1. Scale ratio = drawing…

Q: 50 10 Derive the third projection, taking into account the use of the rules for writing dimensions…

A: GIVEN: TO DETERMINE: TOP VIEW

Q: Q#4: Define Baseline, Main survey line, check line and tie line?

A: - Baseline, main survey line, check line and tie lines are mostly used in triangulation surveying to…

Q: Describe boring spacing and depth?

A: The boring is done for the following purposes- Soil Investigation Determining the depth at which…

Q: Figure below represent contour lines for ground surface and wells located on it 50 w2 W1 fill table…

A: given-water table elevation of wells-W1=60W2=50W3=40

Q: Does the use of a CAD system eliminate the need for trial sketches and other preliminary placement…

A: CAD is the latest technology to design any form of structure. There are so many benefits of this…

Q: How to create border with title box in autocad 2024

A: Steps to create:Border with title box in autocad 2024.

Q: m, tf = 12.80 mm and tw = 7.7 mm. The section is acted by a tensile force and attached to onnectors…

A:

Q: What is the WGS84 datum?

A: WGS84 Datum

Q: Discuss MINIMUM COVER REQUIREMENTS AND STANDARD DIMENSIONS

A: Throughout reinforced concrete, the concrete cover is indeed the shortest route between the layer of…

Q: What is an Elevatio Plan? Give its types as well. How do you draft floor & Elevation plans?

A:

Q: Define the terms Streamlines, Streaklines, Stream tube?

A: Streamlines Streamlines are a family of curves that are outright tangent to the velocity vector of…