In a game of billiards, ball A is given aninitial velocity Vo = 3 m/sec along line DA,parallel to the axis of the table. It hits ballB and then ball C, which are both at rest.Knowing that A and C hit the sides of thetable squarely at points G and E,respectively, and B hits the side obliquelyat F, and assuming frictionless surfacesand perfectly elastic impacts, determinethe velocity Vc with which the ball C hitsthe side of the table at E.2.4m0.6mVA0.9m0.9mV=3 m/s0.6m2.1m

given- a game of billiards in which ball A is given an initial velocity of 3m/s. required- to find…

Answered: and perfectly elastic impacts,…

Engineering

Civil Engineering

and perfectly elastic impacts, determine the velocity Vc with which the ball C hits the side of the table at E.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Question 3 Part a: For the section shown, determine the: • Maximum elastic Moment M Fully plastic…

A: Given Dataσy=250 MN/m2E=200 GN/m2We are supposed to calculate the following parameters.Maximum…

Q: e strength in compression o is 600 N/mm², determine the minimum allowable values of rivet diameter d…

A: Given data Load applied on the plate=15kN Ultimate shear strength of rivet, τ=350 N/mm² Failure…

Q: Q4- A circular shaft consists of steel and aluminum segments is subjected to the torques shown in…

Q: 4,-2 cm 1) Determine the nodal displacements, average element stress values and support reactions…

A: RA+Rd=20RA=20140×90=12.85KNRB=20140×50=7.14KN

Q: Calculate maximum deflection in a simply supported beam under UDL Support Reactions Internal Bending…

Q: Compute the total elongation caused tapering from a width of 120mm to 4 What load P which cause a…

Q: Ipf T One segment has a diameter of d, = 56 mm and length of L, = 1.65 m; the other segment has a…

Q: 2 A leaf spring is made of plates 50 mm wide and 8 mm thick. The spring has a span of 700 mm.…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: Calculate the Tresca and von Mises stresses (in MPa) at points 1 and 2 indicated in the bezel…

Q: 4 - A rectangular block is loaded with a 180 kN axial force and a moment M, as shown in the figure.…

A: Given data: Cross section of column, 100 mm×60 mm Axial load, P=180 kN Maximum allowable tensile…

Q: Vhich of the following is the normal stress

Q: 5-meter steel beam is to be loaded axially by a force P. If the axial deformation on the beam should…

A: Length of Beam = 5000 mm Beam Size = 30mm x 120mm Area of Beam Crosssection = 3600mm2 Elastic…

Q: A soid, crcular ber ABC consists of two segments, as shown in the figure One segment has a diameter…

Q: A solid shaft has length and diameter 'L and Drespectively. A hollow shaft of length L. external…

Q: A slid shaft A of diameter D and length L is subjected to a torque T; another shaft B of the same…

A: Given- Shaft A Shaft B Diameter d1=D d=D/2 Length l=L I=L Torque = T Torque = T

Q: MAXImum STRESS occRS AT THE SUREPCE OF THE BEAM FARTHEST 110 20 Y FROM THE NEUTRAL AXIS + 20 All…

A: Centriody=260×3015+320×20190+110×20360260×30+320×20+20×110=129.57mmBy Parallel Axis…

Q: Q1: For the loaded simply supported beam shown in figure, if the allowable bending stress is 100 MPa…

Q: From the given system as shown. Solve for the axial deformation in the middle 50 AN 100 N 100 AN…

Q: A solid shaft has length and diameter 'L' and Drespectively. A hollow shaft Both are of the same…

A: To Determine Ratio of the torsional stiffness of the hollow and the solid shafts.

Q: Find the total deformation for the bar shown in fig. if the axial loads are applied if cross section…

Q: Q10 A cast-iron beam 10 m long and supported as shown in Fig. carries a uniformly distributed load…

A: Given :Length =10m Allowable stress in…

Q: Question 5 (a)-Determine the natural frequency of vibration and mode shape corresponding to first…

A: The objective of the question is to determine the natural frequency of vibration and mode shape…

Q: Find the total deformation for the bar shown in fig. if the axial loads are applied if cross section…

A: Given: A = mm2, E = GPa

Q: 350mmi The simply supported beam has an l-shaped cross section. (1) Determine the values and…

A: Bending stress is linearly proportional to depth. Compressive and tensile stress have same value but…

Q: 350 mm 20KN /m 100mm 10KN/m 100 mm 330mm 4m 3m 1m 100mm 250 mm AXIS OF SYMMETRY

Q: 1.) The total area of the section in in² 2.) The gross moment of inertia in inª 3.) The cracking…

A: Compressive strength of concrete, f'c = 4000 psiFlexural strength of concrete, fr = 7.5Reinforced…

Q: The 9-lb block has a velocity of 6.72 ft/s when the force of F = (257.6t2) Ib-ft/sec2 is applied.…

A: Determine the velocity of the block when t = 2.40s

Q: AW14x22 beam is subjected to a moment of 99 ft-kips. What is the bending stress in the beam in psi?…

A: Given data - Section W14×22Moment = 99 kips- ft Find out - Bending stress in beam ?

Q: B F2 C D F4 F1 A. F6 F3 F5

A: in member AB member force is 20KN in member BD member force is 32 KN in member DE member force is…

Q: Q1- A simply supported reinforced concrete beam has a cross-section as shown in the Figure 1.Using…

A: Pmax = 65 kN

Q: Prob. 4.3-1. A bimetallic torsion bar consists of a steel core (G, = 75 GPa) of diameter d, = 25 mm…

Q: Analyse the portal frame shown in the figure according to plastic theory and determine whether the…

A: Solution: Plastic Analysis of a frame: Beam mechanism: Load factor = 2 δ=2θ 2×14δ =…

Q: °. Determine the magnitude of the largest torque TA that may be applied at A.

A: Determination of Maximum Torque that can be applied on given shaft in given conditions ##Solving by…

Q: Problem 6.2: The aluminum rod ABC (E=10.1x10 psi) (Figure 6.19), which consists of two cylindrical…

A: Deformation in Aluminium Rod ABC: δ=δAB+δBCδ=PLAEAB+PLAEBCArea (AAB)=π4×1.52=1.76 in2Area…

Q: The average normal stresses developed in section a-a of the turnbuckle, and the bolt shanks at B and…

Q: The figure shows the stress condition of an I-section beam at point A. With the Mohr circle method;…

Q: 2. An AISI 4142 steel Q&T at 800°F exhibits Syt = 235 kpsi, Syc = 285 kpsi, and &f= 0.07. For the…

Q: A very lange thin plate is centered in a gap of width Co.06m) with different oils of unknown…

A: Viscosity is a proportion of a fluids affinity to fluid. There are two kinds of viscosity commonly…

Q: -Determine the maximum force P that can be applied without causing movement of the 90-kg crate that…

Q: Bending Stress in Beam A symmetrical l-section is 200 mm deep and its moment of inertia about…

A: Given- Depth of the I-section, d = 200 mm Moment of inertia about centroidal axis,I=50×106 mm4…

Q: An A913 Gr. 60 W14x109 is used as a 15-m high column. The column is fixed at both ends and is…

Question

In a game of billiards, ball A is given an
initial velocity Vo = 3 m/sec along line DA,
parallel to the axis of the table. It hits ball
B and then ball C, which are both at rest.
Knowing that A and C hit the sides of the
table squarely at points G and E,
respectively, and B hits the side obliquely
at F, and assuming frictionless surfaces
and perfectly elastic impacts, determine
the velocity Vc with which the ball C hits
the side of the table at E.
2.4m
0.6m
VA
0.9m
0.9m
V=3 m/s
0.6m
2.1m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The front-axle beam of a motor vehicle carries the loads shown. The axle is of I-section: flanges 7.5 cm by 2.5 cm, web 5 cm by 2.5 cm. Calculate the tensile stress at the bottom of the axle beam. 20 KN 40cm 20 KN 20 KN 40cm 20 KN
Q6 -Determine the maximum force P that can be applied without causing movement of the 90-kg crate that has a center of gravity at G. The coefficient of static friction at the floor is us = 0.5, as shown in the Figure 10. Fig. (10) 1.2 m 0.5 m 0.5 m 0.7 m 1 m
34 Q₁ Find the cracking Moment for the beam section Shown in figure below if fr = 3.13 Mpa ▸ fc = 20 mpa, Es=200000 mpa. 500 MM 500 MM 100 MM 300 MM 4025 +4 mm
Plz do not use gpt if u use chatgpt i will downvote you again don't use chatgpt
Q₂ for for the ystem showing complute The qixah deformation at A, B 4. A=160mm 2 E=90061 5KN/m + ↓ 3m tram obm 15 KN 444=1.5 A=350 6-75 & for B
Cracking moment.
Strength of material
Please solve the reactions and draw the shear and bending moment diagrams for the beam shown using the Consistent Deformation method.
Question 3 Part a: For the section shown, determine the: Maximum elastic Moment M Fully plastic moment Mf Shape factor a If loaded about the horizontal axis o, = 250MN/m²; E = 200GN/m² ● Part b: Determine the bending moment necessary to cause yielding to a depth of 10mm from the top and bottom surfaces. If after applying this load it is subsequently removed. What will be the residual stresses which will result at A and B when the load is removed? 10 40 Yielded region 40 Fig. 3a 10 ΝΑ Fig. 3b ΝΑ
A concrete beam is reinforced by three steel rods placed as shown. The modulus of elasticity is 3* 106 psi for the concrete and 30 *106 psi for the steel. Using an allowable stress of 1350 psi for the concrete and 20 ksi for the steel, determine the largest permissible positive bending moment in the beam.