An overhang beam carries a distributed load "w" and a concentrated load "P". If the maximum negative shear is -230.08333333333kN and the vertical reaction of hinge support is 209.91666666667KN, determine the following unknowns. (DRAW THE SHEAR AND MOMENT DIAGRAM) Let L1 = 4m and L2 = 1m L1 L2 Solve the value of "w": kN/m Solve the value of "P": kN Solve the reaction of the roller supp

An overhang beam carries a distributed load "w" and a concentrated load "P". If the maximum negative shear is -230.08333333333kN and the vertical reaction of hinge support is 209.91666666667KN, determine the following unknowns. (DRAW THE SHEAR AND MOMENT DIAGRAM) Let L1 = 4m and L2 = 1m L1 L2 Solve the value of "w": kN/m Solve the value of "P": kN Solve the reaction of the roller supp

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find the bending moment diagram. A is fixed, B is pinned. EI is constant.
Theory of structure L=10 ft Udl =4k/ft
41. FIND a. Vertical reaction at C b. Horizontal reaction at C. c. Axial force at member AB.
The beam supports the loads as shown in the figure. Using E=200 GPa, w = 16 kN/m, P = 16 kN and M = 24 kNm, L1= 3 m, L, = 5, L3= 2 m and a=35 mm. Find, a. by double integration method find the ElS at the right end of the beam b. by double integration method the maximum Elő between supports c. If w is spread over L-and L7, and P and M are interchanged, determine the midspan Eló and deflection by moment- area method. 4a W 10a M D 7a
The internal shear force V at a certain section of a steel beam is 79 kips. If the beam has the cross section shown (assume a = 2.1 in., b₁ = 3.5 in., b₂ = 7.6 in., tw = tf = 0.6 in., d = 11.6 in.), determine: (a) the value of Q associated with point H, which is located 2.1 in. below the top surface of the flanged shape. (b) the maximum horizontal shear stress Tmax in the flanged shape. a H d
The pole is supported by a pin at B and A-36 steel guy wire AC. If the wire has a diameter of 0.2. Modulus of Elasticity of Steel = 200GPA or 29x103 ksi Poisson's ratio of steel=0.321 3 ft 30 D 2.5 kip 4 ft B 1. At what angle is the principal stresses on pole BC? Use Mohr's Circle. 2. What is the principal stress in pol BC? Use Mohr's Circle 3. Draw the stresses on a unit element acting on 35-degree clockwise direction of pole BC. Use Mohr's Circle. 4. What are the principal stresses in point D? Use Mohr's Circle. (answer in ksi) 5. At what angle is the principal stresses acting on point D? Use Mohr 's Circle. 6. Draw the stresses on a unit element acting on 35degree-clockwise direction of point D. Use Mohr's Circle. (answer in ksi)
determine the shear force and bending moment at point 1 (P1) in the figure.
For the beam and loading shown, (a) Use discontinuity functions to write the expression for w(x). Include the beam reactions in this expression. (b) Integrate w(x) twice to determine V(x) and M(x). (c) Use V(x) and M(x) to plot the shear-force and bending-moment diagrams. Let a = 5.0 m, b = 1.7 m, wA = 16 kN/m, and wB = 46 kN/m. Label all significant points on each diagram and identify the maximum shear force and bending moment along with their respective locations. Clearly differentiate straight-line and curved portions of the diagrams. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
For the beam and loading shown, (a) Use discontinuity functions to write the expression for w(x). Include the beam reactions in this expression. (b) Integrate w(x) twice to determine V(x) and M(x). (c) Use V(x) and M(x) to plot the shear-force and bending-moment diagrams. Let a = 3.0 m, b = 1 m, WA = 18 kN/m, and wg = 45 kN/m. Label all significant points on each diagram and identify the maximum shear force and bending moment along with their respective locations. Clearly differentiate straight-line and curved portions of the diagrams. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. WB "| WA X C a Answer: Vmax Mmax KN kN.m B b