An epicyclic train of gears is arranged as shown in Fig. How many revolutions does the arm, to which the pinions B and C are attached, make : 1. when A makes one revolution clockwise and D makes half a revolution anticlockwise, and 2. when A makes one revolution clockwise and D is stationary ? The number of teeth on the gears A and D are 40 and 90 respectively.

Q: A gear train is made up of five spur gears as shown in the figure. Gear 2 is driver and gear 6 is…

A: Given data, Figure shown gear train is made of five spur gears. Where,  Gear 2 is driver and gear 6…

Q: for the gear train in below sketch that input gear has 5 kW of power and rotates clockwise at…

A:

Q: In the gear system shown, the motor applies a 190 lb-ft torque to the gear at A. A torque of Tc=392…

A:

Q: (B) Two shafts A (driver) and B (driven) in the same straight line are geared together through an…

A:

Q: Determine the setting for a straight spur gear having 46 teeth of module 4 mm.

A: Given Data⇒ Straight spur gear : Number of teeth(t)=46 teeth Module(d)=4 mm

Q: A pair of spur gears with 20° tooth form transmits 1.0-hp. The pinion is mounted on the shaft of an…

A: Pressure angle is 20 degreeNumber of teeth on pinion is 24Number of teeth on gear is 96Pinion…

Q: calculate the indexing for the following: 1.  1623 divisions 2. 1124 divisions

A: Given DataDivisionsN=16232-N=1124 three plates

Q: The reduction of speed from 360 r.p.m. to 120 r.p.m. is desired by the use of chain drive. The…

A:

Q: (B) The sun and plant gear of an epicyclical shown in figure below the annular gear D has 100…

A:

Q: 1

A: Given data  1. Number of teeth on  Z1=15 2. Number of teeth on  Z2=31 3. Number of teeth on  Z3=17…

Q: A pair of spur gears with 20° tooth form transmits 1.0-hp. The pinion is mounted on the shaft of an…

A:

Q: In the figure below, Gears B and C represent a compound gear and have the following details. The…

A: number of teeth t A=100 tB=40 tc=80 tD=20 input torque  Ti=42 Nm speed of gear A NA=2400 rev/min…

Q: Please answer the attach file

A: The number of teeth of gear 2 is N2=24 teeth. The number of teeth of gear 3 is N3=78 teeth. The…

Q: A 84-tooth gear is driven by a 17-tooth spur pinion. The diametral pitch is 32 teeth/in and the…

A: Given: Number of teeth on the pinion (Tp)=17 Number of teeth on the gear (TG)=84 Diametral Pitch…

Q: Two meshing ge ocity ratio Moc I, e=2 Pressure angle

A:

Q: Below is the arrangement for a gear train. A motor delivers 200-hp at 540-RPM to the input gear A.…

A: The speed of gear A, NA = 540 rpmThe power delivers by motor, P = 200 hp

Q: nning at 100 rpm clockwise. B is an output shaft running at 250 rpm clockwise. Torque on A i

A: given:NA=100RPMNB=250RPMTA=50KN-m

Q: The lath machine in the ( mechanical workshop uses epicyclic gear train snuwn in Figure 1 to…

A: given data; ⇒pitch circle dialmeter (d) of gear  D=214mm⇒module (m)=4mm⇒speed of arm(y)=1…

Q: The figure shows a schematic representation of a gear system. The gears are meshed with one another…

A:

Q: A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has 4 wheels of the…

A: Angular velocity is the rotational velocity of a body. It is equal to the angular distance covered…

Q: consider a planetary train in the figure the number of teeth on gear sol (2) is Z2= 30, the number…

A:

Q: Two parallel shafts, about 550 mm apart are to be connected by spur gears. One shaft is to run at…

A:

Q: 50 teeth A 90⁰ B 80 teeth C 60 teeth

A: Given,  NA= 700 rpm

Q: Two mating spur gears have 40 and 120 teeth respectively. The pinion rotates at 1200 rpm and…

A: Given :- Two spur gear of Z1=40 teeth and Z2=120 teeth  Pinion rotates at N1=1200 rpm  Torque is…

Q: The shaft from a DC motor is connected to gear A which rotates at 45rps in clockwise direction.…

A:

Q: The figure shows a transmission consisting of pulleys and gears. The motor (marked in red) rotates…

A:

Q: Gear 1 has a module of 2 and 26 teeth. This gear drives Gear 2 whose speed is 271.0 rpm. The shaft…

A: Given: The teen on gear 1 is T1=26, The module of gear 1 is m1=2, The speed of gear 2 is N2=271…

Q: Gear 1 has a module of 4 mm/tooth and 25 teeth. This gear drives Gear 2 whose speed is 410 rpm. The…

A: The module of gear 1 is m1=4 mm/tooth. The number of teeth on gear 1 is T1=25. The speed of gear 2…

Q: The spur gearing arrangement  made of two parallel shafts,whose pitch circle diameters of driven and…

A: Gear: The gear is rotating part of the mechanical device. The gears are having the number of teeth…

Q: A two-stage gear train consists of four gears meshed together (Figure 10). The secondand third gears…

A: for the given gear train  To determine  angular velocity of gear 4 in terms of ω1,n1,n2,n3 and n4

Q: Consider the following epicyclic gear trai The number of teeth is indicated in the figure. Crown…

A:

Q: angular speed of Gear 5 is

A: Given data, Gear 2 rotates at 1200 rpm N2= 1200 rpmIt is engages with gear 3 and gear 4 mounted on…

Q: rpm of D in the clockwise direction is

A: Figure shows the epicyclic gear train.For this data is given as: Number of teeth on the gears;…

Q: 1. Classification of gears according to the possibility of movement of gears axis of rotation…

A: Introduction: A gear is a spinning circular machine element with cut teeth or inserted teeth that…

Q: n find the speed of the gear F.

A: Given data: A compound train consists of six gears. the  no teeth on gears as follows:NA=100…

Q: Q(1): For the component epicyclic gear train shown in the figure, the number of teeth of gears (A, B…

A: Given diagram:

Q: Below is the arrangement for a gear train. A motor delivers 200-hp at 540-RPM to the input gear A.…

A: Given:The gear A rotates clockwise CW.Gear B and C are on the same shaft and gear D and E are on…

Q: An epicyclic gear shown in Figure 1 consists of ring gear, planet gear and sun gear. The ring gear…

A: Given Data Ts=32 teeth Tr=72 teeth Arm y=20 rpm

Q: Each of two gears in a mesh has 60 teeth and a module of 6 mm. The teeth are of involute profile.…

A: Data given-  T = 60  m = 6 mm  Arc of contact = 2.5 × circular pitch

Q: The double-reduction helical gearset shown in the figure is driven through shaft 'a' at a speed of…

A: The double-reduction helical gearset shown in the figure is driven through shaft 'a' at a speed of…

Q: Q4: In an epicyclic gear train shown in the figure, the number of teeth of gear (A and S) are (200…

A: For the given epicyclic gear train let C.W. direction be positive and C.C.W. direction be negative.…

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.