An element in plane stress from the frame of a racing car is oriented at a known angle 0 (see the figure). On this inclined element, the normal and shear stresses have the magnitudes and directions shown in the figure. 26.3 MPa 66.3 MPa 23 MPa Determine the normal and shear stresses acting on an element whose sides are parallel to the gy axes; that is, determine og, Oy, and Tzy (a) Determine stress oz. Round to the nearest whole number. MPa (b) Determine stress oy. Round to the nearest whole number. MPa (c) Determine stress Tzy. Round to the nearest whole number. MPa

An element in plane stress from the frame of a racing car is oriented at a known angle 0 (see the figure). On this inclined element, the normal and shear stresses have the magnitudes and directions shown in the figure. 26.3 MPa 66.3 MPa 23 MPa Determine the normal and shear stresses acting on an element whose sides are parallel to the gy axes; that is, determine og, Oy, and Tzy (a) Determine stress oz. Round to the nearest whole number. MPa (b) Determine stress oy. Round to the nearest whole number. MPa (c) Determine stress Tzy. Round to the nearest whole number. MPa

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

170MPA 320MPA 430MPA Figure Q2: State of plane stress
The stresses acting on element B (see figure part a) on the web of a wide-flange beam are found to be o = 11,000 psi in compression in the horizontal direction and oy = 2,600 psi in compression in the vertical direction (see figure part b). Also, shear stresses of magnitude Tzy = 3,200 psi, act in the directions shown. B Side Cross View Section (b) (а) Determine the stresses acting on an element oriented at a counterclockwise angle of 45" from the horizontal. Round your answers to one decimal place. psi psi psi
Consider a point in a structural member that is subjected to plane stress. Normal and shear stresses acting on horizontal and vertical planes at the point are shown. Let T = 39 MPa and o = 19 MPa. Determine the center ocenter of the corresponding in- plane Mohr's circle. 50 MPa -21.56 MPa O -17.85 MPa O -10.87 MPa -14.07 MPa -15.50 MPa
The beam shown below is suspended from two steel rods as shown and is initially horizontal. The midpoint B of the beam is deflected 15 mm downward by force Q. The steel used for the rods has properties E = 200 GPa and σ = 275 MPa, determinea. the required maximum value of Q.b. the deformation of rod AD.c. the deformation of rod CE.
A stress element is subjected to bi-axial loading as shown in figure. P 30° 30° L 30° What will be the maximum principal stress for the given stress element?
An element is subjected to plane stresses as shown in Figure Q1. (i) Determine the normal stress and shear stress acting on the plane that is inclined at 20° as shown in the figure. (ii) Determine the principle major and minor stress and the orientation of the plane where the stresses acting. (iii)Determine the maximum shear stress and the orientation of the plane. 10 N/mm² 30 N/mm² 50 N/mm² 2007 50 N/mm² 30 N/mm² 10 N/mm²
Problem (7.2): The surface of an airplane wing is subjected to plane stress with normal stresses ax, Oy and shear stresS Try, as shown in the Figure (7.31). At a counterclockwise angle 0=30° from the x axis the normal stress is 35 MPa tension, and at an angle 6 = it is 10 MPa compression. If the stress o, equals 100 MPa tension, what are the stresses oy and Try? 50° %3D Oy Txy Ox=100 MPa 7 31)
A rectangular piece of material is subjected to tensile stresses of 83 and 65 N/mm on mutually perpendicular faces. Find the strain in the direction of each stress and in the direction perpendicular to both stresses. Determine also the maximum shear strain in the plane of the stresses, the maximum shear stress and their directions. Take E=200 000 N/mm² and v=0.3. Ans. 3.18×10 4, 2.01×10-4, –2.22×10-4, 7max=1.17x10-4, Tmax=9.0 N/mm² at 45° to the direction of the given stresses.
The tubular shaft shown in the figure has an external diameter of D = 5.5 in. and an internal diameter of d = 2.75 in. and is subjected to a torque of T= 6825 lb-in. [theta = 31 deg] What is the shear stress at A?in psi What is the shear stress at B?in psi What is the shear stress at C? What is the shear stress at D?in psi What is the shear stress at E?in psi