An ammeter is connected to the circuit (see the figure) for measuring the current passing through the load resistor. What is the loading error percentage for the ammeter if the ammeter has an internal resistance of 200 Ohm? (RT = 1:4kOhm, R = 4kohm)

Q: Three 47.1 ohm resistors and three 17.1 H inductors are all in series with a 37 volt battery and a…

A:

Q: Given the zener voltage at 9V and the zener power at 1W, what is the range of allowable values of Iz…

A: Given data, Zener voltage VZ=9 V Zener power Pz=1 W

Q: Correct me if i am wrong I have studied different formula formula for saturation current.

A: Both are correct.

Q: Is there a limit to the series voltage a chain of these batteries can achieve?

A: we need to explain given statement.

Q: (b) The input waveform for the clamper circuit configuration in Figure 3(b) is shown in Figure 3(a).…

A: The solution is given below

Q: The error for an ammeter is found as ±2%, the true range of the current it can give for 10 mA is

A: Given: The error for an ammeter, error=±2% Current, I=10 mA

Q: Questions: 1. What is the threshold voltage, VTH and minimum current that will turn ON the LEDS?

A: As per our policy i have attempted only one question: LED: The full form of LED is a light-emitting…

Q: 10KN Vin Vout 5V 5V Figure 3

A:

Q: What is the corrosion current when the circuit resistance is 0.25ohms and the potential difference…

A: In this questionWe need to determine the current in the corrosion if voltage across the circuit is…

Q: We want to make a resistivity measurement. How should we connect the probes of the multimeter? Drag…

A: a multimeter is a portable device that can be used to take various electrical measurements like,…

Q: Q) What should be the value of R such that maxin power tansfer can take place from the rest of th…

A:

Q: Calculate the base current for this circuit. +12V 12.5 ka 2 ka silicon Select one: a. 0.904 mA O b.…

A:

Q: A voltmeter reads 100.5 V. The error taken from an error curve is 5%. Find the true value of the…

A: Given data:Required information:

Q: Determine the voltage with respect to ground at each point in Figure. Assume the practical model. 25…

A:

Q: If we use 5000 µF, we can get a very low ripple voltage. But this is so bad and this a disadvantage,…

A: According to the given question we are using a 5000 micro farads capacitance , then there is a…

Q: When you connect a voltmeter to read a dc voltage   a. polarity is not important b. connect the…

A: In this question,  We need to choose the correct options When you connect a voltmeter to read a dc…

Q: what is the power disipated by R1

A:

Q: what can be observed in series wherein resistors with the same ohmic value

A:

Q: What is the internal resistance of a voltmeter having a 10KOhm/V sensitivity and set on the 0-100V…

A: Let us find the internal resistance of the voltmeter on a full scale reading. The sensitivity of the…

Q: Rectifier Circuit for nos. 1 to 7. Determine the reading of each meter and PLave. 220V 1k V2 V3

A:

Q: * What is wrong with this circuit? R₁ 10 kn V₁ 24 V 1N4744A 1 15 V The zener is open. O The zener is…

A: We need to check whether diode is on or off

Q: 2. Fre he üzcuits shown below using idenl diodes, tind the values of Ohe labeled vilHuges and anz…

A: [a]

Q: R1 1 ww- High voltage de supply C Us R2 10W 8 3W

A:

Q: If you reverse the flow of electricity in a converter, it then becomes an?

A: From the INVERTER concepts

Q: What is the correct formula to calculate the efficiency of a solar PV device? n=A/PxE n=E/PxA…

A:

Q: Three condensers of 6, 10, and 15 micro-farads are connected in series across a 200V supply. If the…

A: Given, C1=6 μFC2=10 μFC3=15 μFV=200 V

Q: sketch a diagram showing the ohmeter face for a reading of 1.2 k resistance indicate the setting of…

A: The use of an ohmmeter is to measure the resistance between its leads. This resistance between its…

Q: Design a multi range d.c. mille ammeter using a basic movement with an internal resistance R = 5092…

A: Solution !!

Q: reading is due to the a. insertion O b. loading effect с. c. battery aging d. O d. conversion

A: In this question we will write about loading effect....

Q: Attempt Only if you are sure . a 24 V DC voltage source is controlled by a rotational potentiometer.…

A: Given data At θ=0°C, V0°C=24 V At θ=12°C, V12°C=10 V To find out We have to determine the voltage…

Q: VT= 10 V A R₁ 150 $2 R₂ 15 $2 R3 1052 B + Lo

A:

Q: an ammeter has a range of (0-5a) and an accuracy of ±1% of f. s. d. what is the measured value for…

A:

Q: What is a clamp-on ammeter and what electrical principal does it operate

A: we need to answer What is a clamp-on ammeter and what electrical principal does it operate

Q: Three condensers of 6, 10, and 15 micro-farads are connected in series across a 200V supply. If the…

A: Condenser: In an air conditioner  the coolant is injected into condenser, hot and vaporous where it…

Power Measurement

According to Blondel's theorem, the total power is measured with one less number of wattmeters than the number of wires present in the system. So, a single-phase and two-wire system will require one wattmeter and a single-phase and the three-wire system will require two wattmeters, and a three-phase and the three-wire system will also require two wattmeters and a three-phase and the four-wire system will require three wattmeter devices. The wattmeter is a device that measures power using one voltage and one current input as shown in the above figure. Multiple current or voltage input pair cables are used by many power analyzers and digital storage oscilloscopes (DSOs) for measuring watts, in effect within a single instrument acting as multiple wattmeters. It is possible to measure three-phase and four-wire power with one correctly specified power analyzer.