An air refrigeration system operating on a closed cycle is required to produce 14.2 Tons of refrigeration with a cooler pressure of 1550 kPa and a refrigerator pressure of 448 kPa. Leaving air temperatures are 25°C for cooler and 5°C for refrigerator. Assuming an ideal cycle with isentropic compression and expansion, no clearance and no losses, determine (a) mass flow rate of air (b) compressor displacement (c) expander displacement, and (d) COP

An air refrigeration system operating on a closed cycle is required to produce 14.2 Tons of refrigeration with a cooler pressure of 1550 kPa and a refrigerator pressure of 448 kPa. Leaving air temperatures are 25°C for cooler and 5°C for refrigerator. Assuming an ideal cycle with isentropic compression and expansion, no clearance and no losses, determine (a) mass flow rate of air (b) compressor displacement (c) expander displacement, and (d) COP

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Thermodynamics Instructions: Draw the T-s and Schematic diagram for this problem
A simple vapor compression cycle uses ammonia as a refrigerant. The vaporizing and condensing temperature are -20°C and 35°C, respectively. The system is to be used in producing 10,000 kg of ice at -15°C from water at 25°C in 25 hours. The specific heat of ice is 2.094 kJ/kg-K and the heat of fusion is 335 kJ/kg. Assume that there are 30 percent losses of the heat to be absorbed from the water. Compute the heat rejected in the condenser in kW. (Use h₂ = 1735 kJ/kg)
A heat engine operated as a reversible Carnot cycle using 1 kg of air as a working fluid between 500 degrees of a high heat source and 27 degrees of a low heat source is operated at 60 cycles per minute. If both the pressure P2 after isothermal expansion and the pressure P4 after isothermal compression are 30Pa, calculate how many kWh of the output power is generated during an hour by this cycle. Air gas constant : 0.287 J/kgK, specific ratio : 1.4 answer : 449.7 kWh
An air-standard cycle with variable specific heats is executed in a closed system with 0.0055 kg of air and consists of the following three processes: 1–2 v = Constant heat addition from 95 kPa and 17°C to 380 kPa 2–3 Isentropic expansion to 95 kPa 3–1 P = Constant heat rejection to initial state Use data from tables. Determine the thermal efficiency. The thermal efficiency is %
Consider a Diesel cycle with cold-air-standard assumptions, and compression ratio of 21. The temperature and pressure at the beginning of the compression process are 320K and 120kPa respectively. The cutoff ratio for this cycle is 1.8. The isentropic efficiency of the compression and expansion process are 85%. Determine the temperature and pressure at the end of each process of the cycle, the heat transfer per unit mass in and out of the air; qin and qout, thermal efficiency of the cycle, and the mean effective pressure of the cycle.
Thermodynamics
A 540,000 kJ/h capacity refrigeration system using Refrigerant 22 and served by a single compressor unit operates at an evaporator temperature of -23 oC and a condensing saturation temperature 40oC. To get rid of the single compressor load, a modification is proposed to use two stage of compression with refrigerant intercooling. (a) Determine the power required in the original system. (b) Determind the power required for the proposed modified system.
An Otto Cycle operating at normal air pressure has a compression ratio of 8. Prior to the isentropic compression process, the air is at a pressure of 100 kPa, a temperature of 35 degrees Celsius, and a volume of 700 cm3. At the conclusion of the isentropic expansion process, the temperature is 850K. Determine the following using the average specific heat value for the temperature range: The quantity of heat delivered in kilojoules.Thermal efficacy
An ideal gas turbine cycle consisting of 2 stages of compression and 2 stages of expansion has an overall pressure ratio of 9. Air enters the compressors at the temperature of 320 K while, being intercooled between the stages. Air enters the first compressor at 100 kPa and the pressure ratio of cach of the compressors are selected in a way that minimizes the total power input for the compressors. The high-pressure turbine (First one) drives the compressors and the low-pressure one produces power output. The compressors and both the high-pressure and low-pressure turbines can be assumed ideal. To increase the efficiency of the cycle a regenerator with effectiveness of 85% is used to recover some heat from the exhaust of the second turbine. In this cycle, air with the temperature of 1400 K enters the first turbine. After expansion in the first turbine, air is reheated to the same temperature at the inlet of the first turbine (1400 K). You can consider constant specific heats of c,=1.005…