All problem solutions must include an FBD. 3-1. The members of a truss are pin connected at joint O. Determine the magnitudes of F, and F, for equilibrium. Set 0 = 60°. 3-2. The members of a truss are pin connected at joint O. Determine the magnitude of F, and its angle 6 for equilibrium. Set F, = 6 kN. 5 kN 70° 30° 7 kN Probs. 3-1/2

All problem solutions must include an FBD. 3-1. The members of a truss are pin connected at joint O. Determine the magnitudes of F, and F, for equilibrium. Set 0 = 60°. 3-2. The members of a truss are pin connected at joint O. Determine the magnitude of F, and its angle 6 for equilibrium. Set F, = 6 kN. 5 kN 70° 30° 7 kN Probs. 3-1/2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q12. A continuous beam is built in at A and is carried over rollers at B and C as shown in figure, AB = BC = 12 m. It carries an uniformly distributed load of 3 kN/m over AB and a point load of 24 kN over BC which is 4 m from the support B. Value of E and I are 200 Gpa and 0.2 x 10-3 m2 respectively uniform throughout. Calculate the fixed end moments. %3D
2.16 Pins at A and D, and a steel rod at B. support the rigid bars ABC and CD. A roller connection exists between the bars at C. Calculate the 50-kN load's vertical displacement at point C. E= 200 GPa %3D A = 300 mm2 L=3 m %3D 50 kN 2 m 2 m C 1.5 m 3 m
2. Determine the force F to move the blocks A and B to the right. The two blocks are being connected by a frictionless pin at both ends of the strut.. u= 0.18 y= 25° a= 40° strut B A LL
Determine the force in each member of the loaded truss. compression. 4.8 m 4.8 m AB= A E Answers: AE = Mi THE BC= i MI D 1 136° 30%/12 KN B 3.7 m- C 22 KN kN kN kN
Asap
Determine the vertical displacement of joint C. B Cross-section of the truss C P The length of the truss AB, BC, AC, L, is 1,580 mm. The applied force at point C, P, is 55 kN. The diameter of the three trusses, D, is 26 mm. The elastic modulus of the three trusses, E, is 240 GPa.
Determine the forces in members BE and CE of the loaded truss. The forces are positive if in tension, negative if in compression.
Determine the equation of the elastic curve for the beam. El is constant. 6 kN/m 15m 45 kN 45 kN
Determine the force in member AC using stiffness method. Take A =0.75 in² and E =29 (10³) ksi.
a) Analyze the structure to determine the forces in each members of the truss shown in figure below by method of joints. State if the members are in tension or compression PI = (12W) where W = 41 P2 = (6W) kN b) Also analyze the truss by graphical method D 3m. 3m. B •6m. 6 m.
II. Solve for the member forces of the truss. INCLUDE NEGATIVE (-) SIGN IF COMPRESSION FORCE. 15KN В 10KN 1.5m E A 45° 3m 3m
SOLVE USING GENERAL PROCEDURE METHOD