Air flows from a 10 cm pipe in which the temperature and pressure are 4-C and 280 kPa, respectively, into a 5 cm pipe in which the pressure is 147 kPa gage. Calculate the velocity and discharge in each pipe, assuming isothermal conditions, standard atmospheric pressure and no losses. The gas constant for air is 287 N-m/kg-K.

Air flows from a 10 cm pipe in which the temperature and pressure are 4-C and 280 kPa, respectively, into a 5 cm pipe in which the pressure is 147 kPa gage. Calculate the velocity and discharge in each pipe, assuming isothermal conditions, standard atmospheric pressure and no losses. The gas constant for air is 287 N-m/kg-K.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Air at 30 deg. Celsius and 110KPa flows at 20N/s through a rectangular duct that measures 160mm x 320mm. Compute the average velocity (m/s) and flow rate (? ^3/s) using gas constant equal to 289 J/kg-K.
A 15 cm diameter pipe has a diffuser at its end. If the velocity of the fluid in the pipe is 10.11 m/s and the pressure in the pipe is 75 KPa absolute, Calculate head loss in mm. Consider Coefficient of velocity is 0.98 and g = 9.81 m/s² the
P-4 fuel (SG = 0.77) flows rough the Venturi meter hown in the figure below with a velocity Vo= 14.8 ft/s in the d1=6.00-in. pipe. In viscous effects are negligible, determine the elevation, h, of the fuel in the open tube connected to the throat of the Venturi meter. Assume h1= 7.70 in., h2= 5.70 ft, d2= 4.00 in.
I need the answer as soon as possible
Air with a mass flow rate of 5 kg/s enters a horizontal nozzle operating at steady state at 450 K, 350 kPa, and velocity of 3 m/s. The nozzle is well insulated. At the exit, pressure is 300 kPa and temperature is 390 K. Using the ideal gas model for air, the area at the inlet is m², and the velocity at the outlet is Are potential effects negligible? Why? m/s. Is heat transfer negligible? Why? Note that you may choose to model the specific heat as constant.
2. Given the figure below, solve for flow rate in the venturi meter. (C = 0.984) 2 (ø - 250mm) 0.3m oil (as2) 0.8m - glycerin (1.86)
A converging -diverging nozzle with a throat area of 0.0036 m^2 is attached to a very large tank of air in which the pressure is 127 kpa and the temperature is 49 C° the nozzle exhaust to the atmosphere with pressure of 105 kpa if the mass flow rate is 0.92 kg/s determine the exit area and mach number at the throat . the flow in the nozzle is isentropic
! Required information Oil flow in a journal bearing can be treated as parallel flow between two large isothermal plates with one plate moving at a constant velocity of 5 m/s and the other stationary. Consider such a flow with a uniform spacing of 0.5 mm between the plates. The temperatures of the upper and lower plates are 40°C and 15°C, respectively. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Vm/s u(y) The properties of oil at the average temperature of (40+15)/2 = 27.5°C are k = 0.145 W/m-K and μ = 0.605 kg/m-s = 0.605 N-s/m² By simplifying and solving the continuity, momentum, and energy equations, determine the maximum temperature and where it occurs. The maximum temperature is 337.32 °C. The location of the maximum temperature is 0.369 mm above the bottom plate.
A closed tank contains 20 m deep water. A hose is connected as shown such that the nozzle (diameter = 1cm) is directed straight up, If the air gage pressure inside the tank is 20©kPa, solve the actual mass flowrate if the coefficient of discharge through the nozzle is 0.6. AIR 20 m O 1.59kg/s O 1.22kg/s O 1.86kg/s O 1.33kg/s
Need asap
dbb
A constant-area duct that is 20 cm in length by 2 cm in diameter is connected to a reservoir through a converging nozzle, as shown in Figure 9.13. For a reservoir pressure and tem- perature of 1 MPa and 500 K, determine the maximum air flow rate in kilograms per sec- ond through the system and the range of back pressures over which this flow is realized. Repeat these calculations for a converging nozzle with no duct. Assume that fis equal to 0.032 and that y - 1.4. f= 0.032 D-2 cm Isentropic flow P1,000 kPa I 500 K 20 cm