A2: FLUID FLOW, FLOW RATE & PRESSURE DROP Problem: 6. At sea level, atmospheric pressure is 14.7 psia (101 325 Pa). A bicycle tire (at sea level) is inflated to 50 psi (344 737 Pa). Determine the gauge and absolute pressures in the inflated tire.

A2: FLUID FLOW, FLOW RATE & PRESSURE DROP Problem: 6. At sea level, atmospheric pressure is 14.7 psia (101 325 Pa). A bicycle tire (at sea level) is inflated to 50 psi (344 737 Pa). Determine the gauge and absolute pressures in the inflated tire.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

i need the answer quickly
5) Air compressor system has an Air tank volume of 100 m³, the pressure gauge shows 10bar at temperature of 50 °C. When the air tank is cool down to ambient temperature at 25°C Please calculate the air pressure change in the tank. 6) Please explain operating principle of the Low Temperature Drier in Pneumatics supply plant system and draw diagram and explain why water can be reduced from the air
The pressure inside a soap bubble of 10 mm diameter above the atmosphere is_ _(o = 0.04 N/m) 2 3 4 32 Pa 16 Pa 160 Pa 0.32 Pa
Please help me with this problem clearly. List two sources of error in the water-filled tube and pressure gauge method of measuring head for a hydro system and how to avoid them. Using this method, a series of measurements up a hill to the source of the stream produces the following heights: 1.5m, 0.7m, 1.0m, 1.9m, 1.6m, 0.3m, and 0.8m. What is the total head for this site? If the flow rate was 0.5 m3s-1, calculate the power available in this stream?
A Pitot-static probe was used to measure the velocity distribution in a water tunnel. The two pressure lines from the probe were connected to a U-tube manometer which uses a liquid of specific gravity 1.7. The maximum velocity expected in the water tunnel was 2.3 m/s. Your job was to select an appropriate U-tube from a manufacturer which supplies manometers of different heights. The cost increases significantly with manometer height. Which of these should you purchase?
Q 2 please
10 m3/min of free air is compressed to 8 bar gauge. What will be the volumetric flowrate of air at the compressor outlet if polytropic coefficient of air is 1.3 ?
Toplam basınç göstergesi Manometre Vana Venturimetre Debiölçer Hazne Pompa Manometre=Manometer Venturimetre=Venturimeter Debiölser-Flaw meter Vana=Valve Pompa=Pump Hazne=Tank Toplam Basınç Göstergesi =Total Pressure Gauge It is desired to display the flow in the venturimeter, How can you determine this? Explain bY. explaining the method vou bave chosen.
I need the answer as soon as possible
A gasoline line is connected to a pressure gauge through a double U gauge.If the pressure gauge reading is 370 kPa, determine the gauge pressure of the pressure line.gasoline. (see img)
Q) The velocity v (m/s) of air flowing past a flat surface is measured at several distances y(m) away from the surface. Use Newton'sviscosity law to determine the shear stress t (N/m³) at the surface (y=0). dv 'dy Assume a value of dynamic viscosity =1.8* 10- N.s/hm² y, m V, m/s 0.002 0.287 0.006 0.899 0.012 |1.915 0.018 3.048 0.024 4.299 (r-7) Use two forward đifference approximations for h=0.006. Estimate the approximate percent relative error, &. b- , (t=?) Use two forward difference approximations with a step size of 0.012 (h=0.012). Estimate the approximatepercent relative error, , e.. (r-?) ApplyRichardson extrapolation. Estimate the approximate percent relative error, & (r=?) Use unequally spaced three data and the first-derivative of a second-order d- Langrange polynomial to evaluate the derivative (y=0) and shear stress. Estimate the approximate percent relative error, Eg Compare the approximate estimates of the error ([ed ) for the formulas used.
%3D Find the pressure in KN/m2 at the center of pipe A. T = 10°C. Oil (S = 0.85) Water 90 cm 150 cm Water 30 cm Mercury (S = 13.6) to 30 cm