A wide-flange beam (see figure) is subjected to a shear force V. Using the following dimensions of the cross section, calculate the moment of inertia and then determine the following quantities. b = 6 in., t = 0.5 in., h = 10 in., h₁ = 8.4 in., V = 28 kips Note: Disregard the fillets at the junctions of the web and flanges and determine all quantities, including the moment of inertia, by considering the cross section to consist of three rectangles. (a) the maximum shear stress max (in psi) in the web psi I Th o (b) the minimum shear stress min (in psi) in the web psi (c) the average shear stress Taver (obtained by dividing the shear force by the area of the web) and the ratio max (Enter your answer for Taver in psi.) aver psi Taver Tmax = Taver =

A wide-flange beam (see figure) is subjected to a shear force V. Using the following dimensions of the cross section, calculate the moment of inertia and then determine the following quantities. b = 6 in., t = 0.5 in., h = 10 in., h₁ = 8.4 in., V = 28 kips Note: Disregard the fillets at the junctions of the web and flanges and determine all quantities, including the moment of inertia, by considering the cross section to consist of three rectangles. (a) the maximum shear stress max (in psi) in the web psi I Th o (b) the minimum shear stress min (in psi) in the web psi (c) the average shear stress Taver (obtained by dividing the shear force by the area of the web) and the ratio max (Enter your answer for Taver in psi.) aver psi Taver Tmax = Taver =

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Rigid bar ABCD is supported by two bars as shown in Figure P2.7. There is no strain in the vertical bars before load P is applied. After load P is applied, the normal strain in bar (2) is measured as –3,300 um/m. Use the dimensions L1 = 1,600 mm, L2 = 1,200 mm, a = 240 mm, b = 420 mm, and c = 180 mm. Determine:(a) the normal strain in bar (1).(b) the normal strain in bar (1) if there is a 1 mm gap in the connection at pin C before the load is applied.(c) the normal strain in bar (1) if there is a 1 mm gap in the connection at pin B before the load is applied.
7. The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the value of torque T that can be applied to the ends of the shaft without exceeding a shear stress of 70 MPa or an angle of twist of 2.50° in the 3.50-m length. Use G = 83 GPa for steel. 100 mm 70 mm 70 mm T A - 2.00 m 1.50 m
Determine the bending stress (in Pa) at the top of the beam at point C for the beam shown below if P = 1700 N, T = 4167 Nm, a = 0.94 m, b = 1.07 m, c = 0.98 m, w = 33 mm, and h = 79 mm . Round off the final answer to one decimal place. P T W Y U A/O А h B k a b C C | 1 D
The beam shown in the figure is subjected to a moment of M = 50 kN.m. Determine the bending stress at point A and B.
6. A tapered bar of length 600 mm is having cross sectional areas of 650 mm? and 350 mm? at two ends. The bar is fixed at the end having larger area and subjected to axial forces 40 kN which is acting axially outwards at the smaller end and 20 kN, acting at a point 200 mm from smaller end and directing axially towards the larger side. The Modulus of Elasticity of the bar is 700 x 103 N/mm2. Model the bar with three finite elements and Determine i The nodal displacements. ii The stresses in each element. iii The reaction force at the support.
A hollow steel beam (cross-section shown in figure 5) is subjected to a vertical shear force of 30 kN.Moment of inertia of the cross is IN.A = 383.33x106 in4.a) Solve to determine the maximum shear stress and its location.b) Solve to determine the shearing stress at fiber 75 mm from the top of beam’s cross-section.
The force P=25 kN is applied to the bracket as shown in the figure. Compute the normal stresses developed at points A and B. A Answer B 1000 mm 100 mm 17.5° P A = 8000 mm² I= 50 x 106 mm4 NA. T 100 mm 77 200 mm
A wide flange is used as a beam that is simply supported at its ends.The properties are shown.A = 19600 mm². by = 229 mmL = 1249 x10^4mm te=14 mm Tx = 25.4 mm tr = 24.9 mm ly = 49.5 x10^4mm d = 623 mm Ty = 50.5 mm If the beam is laterally supported at supports only, determine the allowable bending stress for a length of; 1. 2m 2. 4m 3. 6m 4. 8m
2. Resolve the vector force into its components in the Figure shown. * Z 2m F=80 kN 5m 3m
Problem 8.45 The three bars have a weight of WA = 20 lb, WB = 40 lb, and Wc = 60 lb, respectively. (Figure 1) Figure 1 of 1 > CPCB=0.5 BMBA=0.3 A MAD=0.2 P D Part A If the coefficients of static friction at the surfaces of contact are as shown, determine the smallest horizontal force P needed to move block A. Express your answer to three significant figures and include the appropriate units. μA P= Value Submit Units My Answers Give Up ? Provide Feedback Continue
The cantilever beam shown in Figure A is subjected to load magnitudes of Pz = 3.0 kips and Py = 8.1 kips. The flanged cross section shown in Figure B has dimensions of bf = 7.1 in., tf = 0.55 in., d = 11.5 in., and t = 0.35 in. Using L = 70 in., determine: (a) the bending stress at point A. (b) the bending stress at point B. (c) the angle for the orientation of the neutral axis relative to the +z axis. Note that positive angles rotate clockwise from the+z axis. FIGURE A P₂ L B tw bf D FIGURE B
Part of a two story building is shown in the figure in which a concerte column and a steel column are used in the first and second floor. The compressive force on the roof of the second floor is PC = 400 kN. The compressive force on the first floor is PB = 310 kN. The steel [Esteel = 200 GPa] column is a wide angle steel shape that has a cross section area of A2 = 1850 mm2. The concrete [Econcrete = 30 GPa] column has a circular section with a diameter of d = 530 mm.[L1 = 4.8 m, L2 = 5.8 m] What is the displacement of the column at B?in mm What is the displacement of the column at C? In mm