control systemanswer all step by step (a)A unity feedback system has a forward transfer function as shown in Figure 3(a).KR(s)G(s)=Y(s)(+)Xs+4Xs+5)Figure 3(a)(i)Determine the loop transfer function of the system.(ii)Calculate the angles of asymptotes, crossing point of asymptotes,breakaway point and jo-axis crossing. Consequently, sketch the root locusof the system for K 20.Based on the root locus in 3(a)(ii), evaluate the system response as Kincreases from 0 to +to. Justify your answer.(iii)(b) The transfer function of a unity feedback control system is given as,K(1 + 0.2s)s(s + 2)(s2 +s+ 1)G(s)(i)Sketch the Bode Plot for the system for K= 1.Estimate the system's gain margin and phase margin based on the BodePlot in 3(b)(i).(ii)

Answered: Image /qna-images/answer/219c4295-cea8-4749-964d-fe163175136e.jpg

A unity feedback system has a forward transfer function as shown in Figure 3(a). K Rís)- Glo)- T+1Xs+4Xs +S) Y(s) Figure 3(a) (6) Determine the loop transfer function of the system. Calculate the angles of asymptotes, crossing point of asymptotes, breakaway point and jo-axis crossing. Consequently, sketch the root locus of the system for K 20. (i) (iii) Based on the root locus in 3(a)(ii), evaluate the system response as K increases from 0 to +o. Justify your answer.

A unity feedback system has a forward transfer function as shown in Figure 3(a). K Rís)- Glo)- T+1Xs+4Xs +S) Y(s) Figure 3(a) (6) Determine the loop transfer function of the system. Calculate the angles of asymptotes, crossing point of asymptotes, breakaway point and jo-axis crossing. Consequently, sketch the root locus of the system for K 20. (i) (iii) Based on the root locus in 3(a)(ii), evaluate the system response as K increases from 0 to +o. Justify your answer.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Write a ladder program for two-motor control program, so that when the ignition switch is closed, the first engine works, and when the ignition is opened, the second engine works ? edited 4:02 AM /
QUESTION 24 When an instantaneous contact is needed and the timing relay does not have one a control relay is wired in series with the timer. True False
please type so that i can read it
YOU HAVE ANSWERED THESE TYPES OF QUESTIONS BEFORE. PLEASE JUST ANSWER IT.
Build an interlocking circuit between two induction motors. The RED and GREEN lights indicate whether the motor is on or off. Use two NO Push buttons for interlocking and an Emergency Switch for emergency stop. You can use the ladder or wiring diagram format
Question 2 Draw the control circuit complete with referencing number and terminal number for an overhead crane according to the sequence described below: Figure 5: An overhead crane Press pushbutton S1 (N/O), motor will move forward and green pilot light H1 will turn on for 10 seconds. This is to allow the motor to reach the end limit of the crane. After the motor reaches the end of travel (indicated by the delay time durations), the motor will stop and red pilot light H2 will turn On. • The control supply for this circuit is 48Vac. Safety features must be included where: i. The motor must stop at condition the thermal overload relay tripped and an emergency button S2 is pressed. .
Where can I find the parts and directions for making a vertically coded control unit?
An 11-pin control relay contains three sets of single-pole, double-throw contacts. List the pin numbers by pairs that can be used as normally closed contacts.
Problem 3.) Enumerate each of the following Control system if falls open loop or close loop. a. automatic flat iron b. automatic entrance door c. automatic washing machine d. refrigerator e. thermostat
I need the answer as soon as possible
Explain the use of scr control used to control the speed of the elevator?
Modify Control Circuit such that when an overload condition occurs a red pilot light turns on, leaving the other light on. Note: the overload relay contains only one NO and one NC contacts. Use NEMA symbols and follow the rules for creating relay ladder diagrams. Also, write the rung numbers, numerical cross references, and wire identification numbers on the modified circuit. L1 2 3 Stop 。 To Start 25 $1 Push-to-test علم O 0 S1 OL L2 Pump 1 (2)