A uniform load of q kN/m with variable load length is moving over the bridge shown below. What is the maximum positive moment due to this load at O in kN.m? L1 = 3.8 m L2= 7 m L3= 5.6 m L4= 5.6 m q= 2.3 kN/m Please note: You need to entre one integer number. Key in the result to ONE Decimal Place. For example, 1.2 and not 1 or 1.21 Enter the numeric value without unit. For example, 1.2 and not 1.2 kN L1 L2 L4 Round your answer to 1 decimal place. I O L3

A uniform load of q kN/m with variable load length is moving over the bridge shown below. What is the maximum positive moment due to this load at O in kN.m? L1 = 3.8 m L2= 7 m L3= 5.6 m L4= 5.6 m q= 2.3 kN/m Please note: You need to entre one integer number. Key in the result to ONE Decimal Place. For example, 1.2 and not 1 or 1.21 Enter the numeric value without unit. For example, 1.2 and not 1.2 kN L1 L2 L4 Round your answer to 1 decimal place. I O L3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported beam AB = 10 m has a hollow rectangular cross-section with 16 cm as width, 23 cm as depth and inner thickness as 1 cm is subjected to a point load of 8 N & 7 N acting at C and D respectively and a uniformly distributed load (UDL) of 8 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 1 cm from the top. Take AC = 1 m & CD = 1 m. Solution: i) Reaction force at B = Answer and unit for part 1 ii) Reaction Force at A = Answer and unit for part 2 iii) The distance from B at which the shear Force value changes from "-" to "+" = Answer and unit for part 3 iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = Answer and unit for part 4 v) Moment of Inertia, I = Answer and unit for part 5 vi) Maximum bending stress = Answer and unit for part 6 vii) Bending stress at 1 cm from the top =
The rigid beam BC shown in the figure is supported by rods (1) and (2) that have cross-sectional areas of 190 mm2 and 290 mm2, respectively. A uniformly distributed load of w= 12 kN/m is applied on the rigid beam as shown in the figure. Assume L= 3 m, a= 1.7 m, length of rods= 2.1 m and E= 57 GPa. Determine the force in rod (1)? Determine the force in rod (2)? Determine the normal stress in rod (1)? Determine the strain in rod (1)? Determine the deformation in rod (1)? In mm Determine the deformation in rod (2)?in mm
A very important load on a structure is the pressure load. This loading is simplified for mathematical calculations such as a right triangle. In this case, a vertical (wooden) solid, where the force of the water pressure will be horizontal and is linearly distributed in a triangular shape and the greatest force due to the water pressure at point B is Y kN. Below this structure, calculate the support reactions acting at points A and B. (Disregard the proper weight of the wooden board) X=9 Y=60
MOVING LOADS
1. A simply supported beam with rectangular cross-section is loaded as shown in the figure. Draw the shear and bending moment diagrams and determine the maximum normal stress due to bending. |15 kN 6 kN/m E A В D 120 mm 0.8 m 2 m
A simply supported beam AB = 10 m has a hollow rectangular cross-section with 10 cm as width, 23 cm as depth and inner thickness as 2 cm is subjected to a point load of 8 N & 9 N acting at C and D respectively and a uniformly distributed load (UDL) of 8 N/m starts from mid-span and ends at the right support of the beam. Determine the maximum bending stress and the bending stress at 2 cm from the top. Take AC = 1 m & CD = 1 m. iv) Maximum Bending Moment (Please write the Maximum bending moment valve in "Nm") = v) Moment of Inertia, I = vi) Maximum bending stress = vii) Bending stress at 2 cm from the top =
A circular column is made of concrete [Ec = 4.2(103)ksi] while being reinforced with six steel rods [Est = 29 (103 )ksi]. It is acted upon by an axial force of 30 kip as shown in the figure to the right. Each rod has a diameter of 0.85 in. show free body diagram and solve for the following: a) Force in each steel rod, Pst = ____________________ kip b) Force in the concrete, Pc = ____________________ kip c) Stress in each steel rod, σst = ____________________ ksi d) Stress in the concrete, σc = ____________________ ksi
Q1: A simply supported beam and its cross section are shown in Figure. The beam carries a load of (10 kN) as shown. Its self-weight is (3.5 kN/m). Calculate the maximum bending stress at X- X. 3.5 kN/m 1.2 m B 1 10 kN 1.2 m 1.2 m 3.6 m 100 T 150 mm Hole T 300 200 200 --
Question 3 A beam of a square cross-section (4 cm x 4 cm) is 5 kN/m loaded as shown in figure 3. If force P = 20 kN: (a) Calculate the reactions of the beam. (b) Draw the shear force and bending moment diagrams. (c) calculate the shear force and bending moment at A and B. (a = 3 m, b = 1 m). 2 m A P 2 kN/m 2 m 2 m Figure 3: Supported Beam B-b- 3 m