A truck and trailer combination crossing a 10-m span (Hinge support at A and Roller support at B) has axle loads of 10, 20, and 30 kN separated respectively by distances of 3 and 5 m. a. What is the largest moment that 10kN-wheel will develop in the span? (kN-m) b. What is the largest moment that 20kN-wheel will develop in the span? (kN-m) c. What is the largest moment that 30kN-wheel will develop in the span? (kN-m)

A truck and trailer combination crossing a 10-m span (Hinge support at A and Roller support at B) has axle loads of 10, 20, and 30 kN separated respectively by distances of 3 and 5 m. a. What is the largest moment that 10kN-wheel will develop in the span? (kN-m) b. What is the largest moment that 20kN-wheel will develop in the span? (kN-m) c. What is the largest moment that 30kN-wheel will develop in the span? (kN-m)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

ANALYZE THE STRUCTURE USING CANTILEVER METHOD COMPUTE AXIAL LOAD OF CF MOMENT AT SUPPORT G 50 KN A E 25 KN D G Com H 8m 3m 4m
answer number 3
Welded plate girder.
A reinforced T-beam has an effective depth of 650 mm and is reinforced with 6-25 mm diameter bars. The web width is 330 mm and has a flange thickness of 120 mm. The beam has a span of 6.2 m and has a spacing center to center equal to 2.5 m, fc’ = 21 MPa and fy = 350 MPa. Compute the nominal moment capacity of the beam for positive bending in kN m. Express your answer in one decimal place.
1.) A standard HS truck is moving across a 25-m simple span. The wheel loads are Pa= 36 kN, Pb = 142 kN, and Pc = 142 kN. The distance between Pa and Pb is 4.5 m while Pb and Pc is 7.6 m. a.) Determine Maximum Shear b.) Determine Maximum Moment
B1
A steel pad supporting heavy machinery rests on four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression is 400 MPa. The total load P that may be supported by the pad is 890 kN. Using a factor of safety 3.0 with respect to ultimate strength, determine the outer diameter of the pier (in mm) if the thickness of the cross section is 10 mm. mm
STEEL DESIGN Situation 1: Situation 3: A light crane rail sits on and is securely fastened to a W crane girder. The girder is simply supported on a span of 6 m. The crane wheel loads are as follows: V = 80 kN and H = 8 kN. Assume full transfer of lateral load to the top flange of the girder. An 8-m long steel column is pinned at the top and fixed at the bottom. The column is provided with lateral support at mid-height in the weak direction. Properties: Ix = 178.1 x 10 mm4 Girder properties: ly = 18.8 x 106 mm4 A = 8129 mm²2 Weight = 67 kg/m Sx = 1, 280 x 10³ mm3 Sy = 361 x 103 mm3 7. Determine the critical slenderness ratio. a. 38 c. 27 Allowable stresses: b. 83 d. 41 Fbx = 164 MPa Find the critical buckling load. 9270 kN Fby = 186 MPa 8. 2190 kN 2310 kN a. с. Determine the actual bending stress about the x- axis. 1. b. 4730 kN d. Compute the minimum length of the column for which the Euler's formula is valid if the proportional limit of the steel used is 320 MPa. a. 99.12 MPa С. 93.75…
SITUATION 1: A precast girder of length 20 m is to be lifted at two points at equal distance from both ends. The weight of the girder is 0.10787 oz/mm. And its section modulus is 900,000 mm3. The moment should be made as small as possible. 1. Determine the distance (m) of the pick-up points from each end.
Please 10mins time
Uniform concrete slab has a mass of 2400 kg. Determine the tension in each of the three parallel supporting cables when the slab is held in the horizontal plane as shown.