A triangular-shaped channel is designed to carry 1.2 cu.m./s of water at a velocity of 0.99 m/s. For a most efficient section, what is the depth of flow? Select one: O a. 1.6 m O b. 1.4 m O c. 1.2 m O d. 1.1 m

A triangular-shaped channel is designed to carry 1.2 cu.m./s of water at a velocity of 0.99 m/s. For a most efficient section, what is the depth of flow? Select one: O a. 1.6 m O b. 1.4 m O c. 1.2 m O d. 1.1 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A circular conduit is to satisfy the following conditions: Capacity when flowing full is 0.13…

A: Given data,capacity when flowing full is 0.13m3/secvelocity when the depth is one quarter of the…

Q: A certain part of cast iron piping of a water distribution involves a parallel section as shown in…

Q: The flow in a cylindrical pipe that has a diameter of 0.9 m is 3 m³/min. What is the velocity of the…

A: Diameter of pipe (d) = 0.9m Flow rate (Q) = 3 m3/min Determine the velocity of the water in m/s.

Q: 4) A 150mm x 50mm venturi meter set up is installed in a vertical pipeline. Determine the flow if…

A: To determine the flow-

Q: Water flows under a sluice gate in a horizontal rectangular channel of 2 m wide. If the depths of…

A: In this problem, we are asked to calculate the discharge of water flowing under a sluice gate in a…

Q: Design a coarse screen for a flow 0.45 m3/sec. The screen is placed in a canal 0.9 m in width and…

A: Given data Discharge Width Height of screen Bars dimensions

Q: The channel is made of wood and has a downward slope of 0.0020. Determine the depth of flow y that…

A: Given:- The downward slope of the channel = 0.0020 The value of n = 0.012 To determine:- The depth…

Q: Consider a free-flowing structure with a gate, a rectangular cross-section, and properties given in…

Q: A 10 cm diameter pipe is to carry water at a Reynolds number of 105. The entrance length required…

A: Given 10 cm diameter pipe Reynold's number=105

Q: Water flows in a rectangular channel 10 ft wide at a velocity of 10 f/s (V1) and a depth of 10 ft…

A: v1 = 10ft/s y1 = 10ft w1 = 10ft Q = 10*10*10 = 1000ft3/s q = Q/T = 1000/10 = 100ft2/s E1 = y1 +…

Q: Two tanks A and B. of constant cross-sectiona rea of 10 m² and 2.5 m², respectively, are onnected by…

Q: With a total flow of 14 cfs, determine the division of flow and the head loss from A to B. L = 6000…

A: ASKED: To determine the flow through each pipe and the head loss. Given, Flow rate of the system…

Q: A triangular channel has a width of 5m and the depth of flow in the channel is 2m. The velocity of…

A: Given: Width of channel = 5 m Depth of flow = 2 m Velocity at depth of 0.2 m, V0.2 = 0.8 m/s…

Q: 7. A stream having a discharge of 280L/sec per meter width of channel has a depth after the jump of…

A: Let V1 be the velocity of water before jump. y1 be the depth before jump. - Find Depth before jump…

Q: Calculate the flow discharge in a 7-m-wide rectangular horizontal channel where the flow depth and…

A: Given, width of channel, W = 7m Depth, d = 0.7m Velocity, v= 7m/s To calculate: Discharge (Q)

Q: The top width and the depth of flow in a triangular channel were measured as 4 m and 1 m,…

A: A triangular channel- Top width=4 m, Depth of flow =1 m, Velocity at surface- V=0.7 m/s, Velocity at…

Q: Two people are arguing on the flow regime of water in a certain trapezoidal canal with the following…

A: Q = 0.09m3 /s

Q: What is the magnitude of the velocity where the flows are fully mixed?

A: Continuity equation: - In this equation principle of conservation of mass is applied that is AV =…

Q: Specific energy A horizontal rectangular channel is 12 feet wide and carries a flow rate of 60 cfs.…

Q: Given the properties of the pipelines, together with the elevation of water in the three-reservoirs,…

Q: For the conditions given below, find the mass flowrate (lbm/sec). Density (p) is 62.4 lbm/ft³ 1. The…

A: Diameter of pipe (d) = 18 inch = 1.5 ftLength of flow (L) = 300 ftHazin william coefficient (C) =…

Q: Obtain the volume of flow in L/s that will pass through a 200 mm pipe with a head loss of 3.78 m per…

Q: Find the flow (m³/s) in a 18.6m wide rectangular channel for which the critical depth is 5.6m.

Q: Water flows through a pipe AB with_m diameter and_ m/s then passes through pipe BC with AB (in cubic…

Q: Current Attempt in Progress Determine the flowrate for the symmetrical channel shown in the figure…

A: Given Slope = 0.002

Q: Situation 1: Give the discharge/flow rate in (m³/s) of the system with a constant velocity of 2.5…

A: Given data : The magnitude of velocity of flow is V=2.5 m/s The magnitude of diameter of pipe is…

Q: Water is flowing in a rectangular channel having width 3.85 m and depth 0.86 m. Classify the type of…

A: Given- Width b=3.85 m, Depth y=0.86 m, Discharge Q=8.45 m3/s, It is needed to find the type of flow.

Question

A triangular-shaped channel is designed to carry 1.2 cu.m./s of water at a velocity of 0.99 m/s. For a most efficient section,
what is the depth of flow?
Select one:
O a. 1.6 m
O b. 1.4 m
O c. 1.2 m
O d. 1.1 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The top width and the depth of flow in a triangular channel were measured as 5 m and 1 m respectively. The measured velocity on the centre line of flow area at the water surface, 0.2 m and 0.8 m below the surface are 0.8 m/s, 0.6 m/s and 0.5 m/s respectively. Using two point method of velocity measurement, the discharge (in m3/s) in the channel is
Fluid
Question- A rectangular channel of 3 m width is carrying a discharge of 6 m³/s considering that acceleration due to gravity is 10 m/s², find the velocity of flow in m/s corresponding to the critical depth at which specific energy is minimum.
The top width and the depth of flow in a triangular channel were measured as 4 m and 1 m, respectively. The measured velocities on the centre line at the water surface. 0.2 in and 0.8 m below the surface are 0.7 m/s, 0.6 m/s and 0.4 m/s respectively. Using two-point method of velocity measurement, the discharge (in m³/s) in the channel is (A) 1.4 (B) 1.2 (C) 1.0 (D) 0.8
A triangular channel with most efficient section discharges water at the rate of 1.45 m3/s. Assuming n=0.018 and s=0.0021. Calculate the normal depth of flow in meters. CHOICES 1.05 5.10 1.50 10.5
With a flow of 86.4 cu. m. per sec., determine the approximate diameter size of a pipe in mm considering the allowable head loss of 20 m per 1000 m and the following: a) f-value of 0.018, b) C-value of 80, and c) n-value of 0.015.
q5 (b) The discharge and velocity of flow over the model of a spillway are 4 m3/s and 3.2 m/s, respectively. Determine the velocity and discharge over the prototype, which is 25 times the size of the model. Refer to Table 5(b).
A vertical cylinder having a circular base of radius 'r' and a height of 12 m is filled with water at the rate of 1 m3/min. If the depth of water in the cylinder at the vertical position is 3 m, what would be the resulting depth when the cylinder is in the horizontal position? OA 0.30r O B. 0.40r OC.0.50r O D.0.60r
For type S2, one of the water surface profiles in a variable flow environmenta) Show the schematic position of the profile.b) Determine the sign of the profile.c) Determine the flow of the current depth according to the limit values and show it by drawing a figure.
If u = xy + λy³x. v = -0.5y² + 6x³z and w = 5y²x - y³z + x, then for a steady and incompressible flow, value of λ will be