A triangular duct flows partly full having a bed slope of (0.004) as shown in Fig. (1) below. If the flow depth is (0.6 m), and manning's n = 0.016, compute: 1- Top width 2- Discharge 3- Is the flow subcritical or supercritical? 4- Is the flow laminar or turbulent? 1 m 1m 1m

A triangular duct flows partly full having a bed slope of (0.004) as shown in Fig. (1) below. If the flow depth is (0.6 m), and manning's n = 0.016, compute: 1- Top width 2- Discharge 3- Is the flow subcritical or supercritical? 4- Is the flow laminar or turbulent? 1 m 1m 1m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A horizontal pipe gradually reduces its diameter from 300 mm at point A to 100 mm at point B. The pressures at point A and point B are 100 kPa and 70 kPa, respectively. If the measured flow discharge along the pipe is 15 L's, determine the head loss along the pipe from point A to point B. At the back of this sheet, illustrate the energy grade line and hydraulic grade line of the pipe.
Assume uniform flow through a half-full circular channel. a. hydraulic radius (m) b. Reynolds number c. hydraulic depth (m) d. Froude number
As figure shown, Q1 = 4 ft°/s splits into two equal flow rates and p1 = 20 psig. Neglecting losses, compute pressure (in psig) at point 2 and 3. BOX THE FINAL ANSWER dz =4in 30° (2) Water od, = 6 in 50° dy =3in
Problem 1: A pipeline 300 m long discharge freely at a point 50 m lower than the water surface at intake (Figure 1). The pipe intake projects into the reservoir. The first 200 m is of 350 mm diameter and the remaining 100 m is of 250 mm diameter. (a) Find the rate of discharge assuming f= 0.06. If the junction point C of the two sizes of pipe is 40 m below the intake water surface level, find the pressure head. L₁, D₁, f AZ1 C L2, D2, f T 122 -V₁
Three pipes are in parallel. The total volumetric flowrate through the network is 2.15 cumecs. If the Darcy- Weisbach Friction Factor is 0.015 for both Pipe 1 and Pipe 3, and 0.02 for Pipe 2, determine the volumetric flowrate in Pipe 3. Pipe 1: D₁ = 450mm, L₁ = 800m 1 Pipe 2: D₂ = 400mm, L₂ L2 = 700m Pipe 3: D3 = 500mm, L₁ = 600m O 1.01m^3/s O 0.69m^3/s O 0.94m^3/s O 0.86m^3/s
The flow rate for the pipe system is 0.050 m³/s with a total head loss of 12 m. Use C = 120 for all pipes. 2 3 Pipe Length Diameter 1 400 m 200 mm 2 500 m 180 mm 300 m 4 620 m 250 mm a. Calculate the head loss in pipe 2.2.81 m b. Solve the rate of flow in pipeline 3. 0.0278 m³/s c. Compute the diameter of pipe 3. 176.54 mm Situation: 3
For the pipe network shown below, Problem 4(- f=0.022 for all pipes. Determine the discharge in line be after two corrections (after AQ,' and AQ,' are applied, if applicable). The initial assumed flow rates are provided. Diameters of horizontal pipes in mm are 600 and 500 for others. 400 L/s a b 1000 m 800 m 150 L/s 250 L/s AQ1 150 L/s AQ2 600 m 400 L/s
3. Water is moving between two reservoirs at a flow rate of 0.08 m³/s via the pipes shown in the diagram (D₁ = 10 cm, D₂ = 20 cm). Assume both pipes have a roughness ks = 0.08 mm. If the difference in water surface elevation between the two reservoirs is 70 m and L₁ = 50 m, what is the length of the larger pipe (L2)? Further, what is the entrance length of pipe 1? For what fraction of the length of pipe 1 is flow fully developed? Include form losses due to pipe components (entrance, expansion, and exit) in your calculations. For more info on component losses, use Table 10.5 and 0 = 180°. Water T = 20°C D₁ D₂ 1₂2.
Q2: A is 4500 m length-gas flow line, and B is 2000 m length-liquid flow line (0.1 m diameter) both are connected with left side of 2500 m in length C-pipeline (0.15 m). If the pressure at A-pipeline inlet = 2400 kPa, pressure at C-pipeline out let = 2000 kPa, liquid flow rate = 0.009 m³/s, Gas Oil Ratio = 40 m³/m², PL 680 kg/m³, p=0.922 kg/m³, gas flowing temperature-300 K, base temperature-288 K, base pressure 101.3 kPa, Z-0.9, gas gravity 9.4x10-3 Pa.s, calculate the 0.6, gas viscosity-0.015x10³ Pa.s, and liquid viscosity diameter of gas pipeline and inlet pressure of liquid pipeline? Assume all pipes are flat and horizontal. =
7.15 The following data were taken for turbulent flow in a circu- lar pipe with a radius of 3.5 cm. Evaluate the kinetic energy cor- rection factor. The velocity at the pipe wall is zero. r (cm) V (m/s) r (cm) V (m/s) 0.0 32.5 2.8 22.03 0.5 32.44 2.9 21.24 1.0 32.27 3.0 20.49 1.5 31.22 3.1 19.6 2.0 28.21 3.2 18.69 2.25 26.51 3.25 18.16 2.5 24.38 3.3 17.54 2.6 23.7 3.35 17.02 2.7 22.88 3.4 16.14
5 Two reservoirs are connected by a pipeline, The diameter of the pipe is (0.5 m and the difference in levels of the two reservoirs is 12.5 m. The total length of the pipe is 1000 m. The velocity of flow in the pipe taking into account both major and minor losses will be [Take, friction factor f-0.04 and g 10 m/sec] (a) 1.75 m/s (c) 4.5 m/s (b) 3.2 m/s (d) 0.5 m/s
PROBLEM 1 The total discharge in the system below is 15.5 cfs and the head loss from B to Cis 24 ft. Using n = 0.011 for all pipes, determine the following: (a) flow rate Q2 (cfs) through pipe 2, (b) flow rate Qs (cfs) through pipe 3, (c) flow rate Qa (cfs) through pipe 4, 2000 ft 12 in (d) head loss hu (ft) in pipe 1, and (e) head loss his (ft) in pipe 5. 3000 ft 1500 ft 4000 ft 30 in 10 in 24 in A D 2500 ft 15 in