automatic control A train control system is shown as below. Considering the control system, please find thetransfer function of the Drive System.v, (1) +e(1)KDrive SystemTrainv(1)b(1)Sensor, K,|v, (1): Reference voltage [V]v(t): the velocity of the train [m/ s]K:a constant gain, 100M: the mass of the train, 5000 | N /(m/ s² )||Brnam : the viscous friction coefficient of the train, 0.1 [N /(m/ s)]K, : a constant gain, 0.15 [V / (m/ s)]f(1)The response of the drive system for e, (t) = 1[V], ƒ (1) = 1+ K,e" +K¸e*1s2 + 2s + 13s2 + 4s + 32s2 +s+ 24s2 + 3s + 4

Answered: Image /qna-images/answer/da60a79c-7341-4789-9161-33f5d31e2ee5.jpg

A train control system is shown as below. Considering the control system, please find the transfer function of the Drive System. v, (1) - e(1) (1) K Drive System Train b(t) Sensor, K, |v, (t) : Reference voltage [V] v(1): the velocity of the train [m/ s] K :a constant gain, 100 M: the mass of the train, 5000 |[ N /(m/ s² )]| Bnam : the viscous friction coefficient of the train, 0.1 [N / (m/ s)] K, : a constant gain, 0.15 [V / (m/ s)] S(1) The response of the drive system for e, (1) = 1[V], ƒ (1) = 1+ K,e" + K,e 1 s2 + 2s + 1 s2 + 4s + 3 2 s2 + s + 2

A train control system is shown as below. Considering the control system, please find the transfer function of the Drive System. v, (1) - e(1) (1) K Drive System Train b(t) Sensor, K, |v, (t) : Reference voltage [V] v(1): the velocity of the train [m/ s] K :a constant gain, 100 M: the mass of the train, 5000 |[ N /(m/ s² )]| Bnam : the viscous friction coefficient of the train, 0.1 [N / (m/ s)] K, : a constant gain, 0.15 [V / (m/ s)] S(1) The response of the drive system for e, (1) = 1[V], ƒ (1) = 1+ K,e" + K,e 1 s2 + 2s + 1 s2 + 4s + 3 2 s2 + s + 2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Quèstion 11 Operating time of a primary protection relay is greater than the back-up protection relay True False
What are auto reclosures?
Differential compound motors are preferred to use for elevators True False
5) A Solid State Relay (SSR) can or should be used over a mechanical relay when: a) No mechanical "clicking" sound is desired b) In environments where there is a risk of an explosion from sparks c) Where find dust or particles are present and may contaminate the switch d) All of the above
1. Explain briefly in one(1) sentence what is the function of the squirrel cage winding inthe operation of the synchronous motor.(for 50 points)
Q2 ) I. What is the effect of chang ing the sequence of phases in the electric feeder (single phase, three-phase) motor? How do you correct the defect if necessary?
In Single phase motor starter is used for overload Protection. a. Wire b. MCB c. Relay d. Contactor
Which of the following steps is missing in the open-loop control system sensing the state of the system thinking about what to do to the system doing something to affect the system timing the system
* 12V dc motor can be installed to PLC output pin Directly Via push button Via contactor Via relay
D is the correct option explain properly please
Wire size and voltage drop The cross-sectional area of wire is measured in circular mils (CM). 1 mil = 1/1000 inch CM = squaring of mil Example 1: Find CM for a piece of wire has a diameter of .008 of an inch. .008 = 8/1000 = 8 mils CM = 8² = 64 Find CM for a piece of wire has a diameter of .008 of an inch. 5. Find Cm for a piece of wire has a diameter of .064 of an inch. 6. Find CM for a Wire has 24 strands of wire and each strand is .012 inches in diameter.
Explain regenerative braking in detail , as applied to electric locomotives