A test is conducted to determine the overall heat transfer coefficient in an au- tomotive radiator that is a compact cross-flow water-to-air heat exchanger with both fluids (air and water) unmixed (Fig. 13-22). The radiator has 40 tubes of internal diameter 0.5 cm and length 65 cm in a closely spaced plate-finned matrix. Hot water enters the tubes at 90°C at a rate of 0.6 kg/s and leaves at 65°C. Air flows across the radiator through the interfin spaces and is heated from 20°C to 40°C. Determine the overall heat transfer coefficient U, of this ra- diator based on the inner surface area of the tubes.

A test is conducted to determine the overall heat transfer coefficient in an au- tomotive radiator that is a compact cross-flow water-to-air heat exchanger with both fluids (air and water) unmixed (Fig. 13-22). The radiator has 40 tubes of internal diameter 0.5 cm and length 65 cm in a closely spaced plate-finned matrix. Hot water enters the tubes at 90°C at a rate of 0.6 kg/s and leaves at 65°C. Air flows across the radiator through the interfin spaces and is heated from 20°C to 40°C. Determine the overall heat transfer coefficient U, of this ra- diator based on the inner surface area of the tubes.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 4 a) Each cylinder in a four-cylinder car engine has a bore diameter of 63.53 mm and the stroke for each piston is 175.00 mm. Calculate the cubic capacity of the engine in cm? and calculate the clearance volume per cylinder for a compression ratio, r, of 6.25. b) The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32 mm and the stroke of each piston is 125 mm. During testing., the engine runs at 1450 revolutions per minute (rpm) with a pressure-volume indicator diagram showing a mean net area of 2.90 cm and a diagram length of 0.85 cm. The pressure scale on the indicator diagram is set to 165 kN/m per cm. Calculate the mean effective pressure (m.e.p) and the indicated power in kilowatts (kW) developed by this six-cylinder four-stroke engine. Give your answer to 2 decimal c) A hollow connecting rod has an inner diameter of 26.25 mm and is subjected to an axial tensile load of 500 MN. If the maximum allowable stress for this hollow rod…
Hello ! I hope you are well.Why are we taking this specific cross section for the second part of the question ? Is it because it's the one where the nails are ?
Kindly answer correctly. This is urgent. Thanks in advance
3d
i need the answer quickly
2) A washer is going to be manufactured by cutting operation out of 2024ST aluminum alloy sheet that has a thickness of 2.5 mm. The outside diameter of the washer is 25.0 mm, and the inside diameter is 12.0 mm. Make a rough sketch, define the geometries to be used and determine a. The punch and die size for the blanking operation b. The punch and die size for the punching operation c. The force required performing the blanking and punching operation simultaneously. The aluminum has a tensile strength = 300 MPa.
26c)A material has an mean indentation diameter of 3.64 mm created by a 5 mm diameter Brinell Indenter. Its hardness value is 200 HB , what will be applied force in Newtons?
what type of grinding wheel should be used to get the required finish on this part using a surface grinder?
26. A JELLO IS sußJECTED TO %3D 0) DRAW THE DEFORMEO SHAPE CALCULATE ?
The possibility to make the required shape from the material is considered during design specification. Select one: O True O False
Match patterns representing different materials are allowable and specified by drawing standards. True? A. Yes B. No, they may be represented at the engineering discretion Instead of using multiple sections for different features, I can cluster them under a single section using A. An offset section B. A half section C. A Multiview section D. None of the above
Select the correct statement regarding the solid model shown below. pattern1 It is easiest to create the 18 holes in this model by sketching each individual hole and using the extruded boss/base feature. It is easiest to create the 18 holes in this model by sketching one individual hole