A string is wrapped around a thin-walled cylinder pulley of radius 11.5 cm and mass of 14 kg. If the string is pulled by a force that is tangent to a point on the rim of the pulley, how much force is exerted to cause it to rotate at a constant rate of 3.92 rad/s? The moment of inertia for thin-walled cylinder is I = mr². 0.726 N 54.9 N 6.31 N 477 N

A string is wrapped around a thin-walled cylinder pulley of radius 11.5 cm and mass of 14 kg. If the string is pulled by a force that is tangent to a point on the rim of the pulley, how much force is exerted to cause it to rotate at a constant rate of 3.92 rad/s? The moment of inertia for thin-walled cylinder is I = mr². 0.726 N 54.9 N 6.31 N 477 N

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

In the figure, two 7.60 kg blocks are connected by a massless string over a pulley of radius 1.30 cm and rotational inertia 7.40 x 104 kg-m2. The string does not slip on the pulley; it is not known whether there is friction between the table and the sliding block; the pulley's axis is frictionless. When this system is released from rest, the pulley turns through 1.20 rad in 154 ms and the acceleration of the blocks is constant. What are (a) the magnitude of the pulley's angular acceleration, (b) the magnitude of either block's acceleration, (c) string tension T, and (d) string tension T? Assume free-fall acceleration to be equal to 9.81 m/s?.
A circular disk with a radius of 0.38 m is subject to 2 tangentially applied forces. The disc is fixed such that it will rotate about its center. Both forces produce a torque in the same direction. The mass of the disc is 0.73 kg. The moment of inertia of a disc is I =1/2MR^2 F1 = 2.3 N applied at the outer edge of the disc. F2 = 3.6 N applied at a distance of 0.29 from the center of the disc. What is the angular acceleration of the disc?
An object's moment of inertia is 2.50 kgxm^2 . Its angular velocity is increasing at the rate of 3.30 rad/s^2 . What is the net torque on the object?
A circular disk with a radius of 0.38 m is subject to 2 tangentially applied forces. The disc is fixed such that it will rotate about its center. Both forces produce a torque in the same direction. The mass of the disc is 0.73 kg. The moment of inertia of a disc is I = 1/2 MR^2 F1 = 2.3 N applied at the outer edge of the disc. F2 = 3.6 N applied at a distance of 0.29 from the center of the disc. What is the angular acceleration of the disc?
A circular disk with a radius of 0.5 m is subject to 2 tangentially applied forces. The disc is fixed such that it will rotate about its center. Both forces produce a torque in the same direction. The mass of the disc is 0.69 kg. The moment of inertia of a disc is I MR² = F₁ = 2.6 N applied at the outer edge of the disc. F₂ = 4 N applied at a distance of 0.26 from the center of the disc. What is the angular acceleration of the disc?
A wind turbine is initially spinning at a constant angular speed. As the wind's strength gradually increases, the turbine experiences a constant angular acceleration 0.107 rad/s². After making 2870 revolutions, its angular speed is 130 rad/s. (a) What is the initial angular velocity of the turbine? (b) How much time elapses while the turbine is speeding up? (a) Number i 129.848 Units rad/s (b) Number i 1.327 Units S
Please answer E16,E17
A cylinder is rotating about an axis that passes through the center of each circular end piece. The cylinder has a radius of 0.110 m, an angular speed of 64.0 rad/s, and a moment of inertia of 1.08 kg-m². A brake shoe presses against the surface of the cylinder and applies a tangential frictional force to it. The frictional force reduces the angular speed of the cylinder by a factor of 9 during a time of 8.00 s. (a) Find the magnitude of the angular deceleration of the cylinder. (b) Find the magnitude of the force of friction applied by the brake shoe. (a) Number i (b) Number i Units Units
2 W S X 24919 3 E D C 3. A dentist causes the bit of a high-speed drill to accelerate from an angular speed of 1.45 x 10¹ rad/s to an angular speed of 3.75 x 104 rad/s. In the process, the bit turns through 2.26 x 10¹ rad. Assuming a constant angular acceleration, how long would it take the bit to reach its maximum speed of 7.10 x 10 rad/s, starting from rest? $ R F V % 5 19 T G tv B MacBook Air 6: Y H & 7 N 44 U ★ 8 J P M ( 9 K MOSISO V H 2 command 4 option y m 04 M
A 4.0 m long thin rod is pinned so that it spins about its center. The rod has a rotational inertia of 8.0 kg m2 about this center. The rod has two 3.0 kg masses attached at each end. What force F must be applied to one end to make the system rotate with an angular acceleration of 4.0 rad/s2 about its center?
A circular disk with a radius of 0.51 m is subject to 2 tangentially applied forces. The disc is fixed such that it will rotate about its center. Both forces produce a torque in the same direction. The mass of the disc is 0.58 kg. The moment of inertia of a disc is I = MR² F₁ = 2.5 N applied at the outer edge of the disc. F₂ = 5.1 N applied at a distance of 0.29 from the center of the disc. What is the angular acceleration of the disc?
A 150 g baseball is pitched at 32.8 m/s and spinning at 42 rad/s. You can treat the baseball as a uniform solid sphere of radius 3.7 cm. What fraction (in %) of its kinetic energy is rotational?