A straight pipe AB, of length 10 m, tapers from a diameter of 40 cm at A to 20 cm at B. The centre line of the pipe is so located that the end B is 2 m above the level of A. Liquid of specific gravity 0.9 flows through the pipe at 150 litres/second. Pressure gauges connected at A and B show the readings of 60 kPa and 40 kPa, respectively, Determine the direction of flow.

A straight pipe AB, of length 10 m, tapers from a diameter of 40 cm at A to 20 cm at B. The centre line of the pipe is so located that the end B is 2 m above the level of A. Liquid of specific gravity 0.9 flows through the pipe at 150 litres/second. Pressure gauges connected at A and B show the readings of 60 kPa and 40 kPa, respectively, Determine the direction of flow.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

asnwer asan with neat solution thank youGiven the figure below, (a) determine the flow rate in the siphon shown. Diameter of the pipe is 2.5cm.(b) Determine the pressure at point B.
Please indicate the given, assumption and iluustration A steel pipe, 3.5 km long x 80 cm diameter x 1 cm wall thickness, conveys water at the rate of 1.75 m3/s. Determine the increase in pressure when a valve provided at the downstream end of the pipe is closed instantaneously. Consider pipe to be elastic and take bulk modulus of water K = 2x109 N/m2; Modulus of elasticity of steel E = 2x1011 N/m2. After determining the surge of pressure in the pipe, compute the following: A) The Longitudinal Stress of the Pipe in Pascal. B) The Circumferential Stress of the Pipe in Pascal.
i)Calculate the flow rate through the system.
A cylindrical tank of water is 20 m in diameter and 3.5 m tall. There is a 1.0 cm diameter hole at the bottom from which water is leaking. A feeder pipe at the top of the tank, 4.0 m above the ground delivers water at a rate of 0.02 m/min. Ir the tank is initially half full, tal what is the water flow rate in m^3/sec from the top feeder pipe? (bi what is the pressure at the bottom of the tank? (Hint: Bernoul's principle) () what is the water speed at the bottom? (d) what is the leaking flow rate at the bottom? fe) at what rate is the volume of water changing? (Assume the tank is open to air at the top)
The pipe bend shown is in a horizontal plane. Oil with a specific gravity of 0.86 enters the reducing bend at section A with a velocity of 3.2 m/s and a pressure of 150 kPa. Neglecting head loss, determine (a) The velocity at section B, V3 (m/s) (b) The pressure at section B, ps (kPa) (c) FMx (N) de = 100 mm B da = 150 mm 30°
Please submit the png solution.
Q3. SAE 30 oil (Sp. Gr. =0.833) with a dynamic viscosity 0.28 N.S/m? flows in a 4-cm-diameter pipe which is inclined with an angle 37°. For the pressure measurement shown, determine A. Whether the flow is up or down The flow rate in m'/h C. The shear stress and velocity 1 cm from the boundary Draw the shear stress and velocity profile with the section of the pipe. В. D. P-180 kPa P- sOokPa 15m 20m
An ideal liquid flowing through a pipe A of cross-section 0.2m² with velocity 10m/s enters a T-junction. One side of the T-junction B has cross-section area 0.1m² and the other side Chascross-section area 0.05m². If the velocity of water in C is 15m/s then in B the velocity is
nat3
A 25-mm-diameter pipe 35m long is used to convey oil. The oil has a density of 880kg/m³ and a kinematic viscosity of 0.25×10*m³/s. The discharge in the pipe is Q=24x10*m³/min. Given that the pipe is placed horizontally and there are no any minor losses. Determine the pressure drop between the entrance and exit of pipe.
the marked answers are correct. Expalin the steps