A steel shaft with a diameter 45 mm and length 1.30 m transmits 55.50 kWfrom an electric motor to a compressor. The allowable shear stress is 51.75MPa and the allowable angle of twist is 2.1 degrees. G=83 x 10^3 psiDetermine the polar moment of inertia (in mm^4) of the steel shaft. *3 points(Please DO NOT USE SCIENTIFIC NOTATION in your final answers. Please write final answers to4 decimal places.)Your answerDetermine the required torque (in N-m) as limited by stress. *4 points(Please DO NOT USE SCIENTIFIC NOTATION in your final answers. Please write final answers to4 decimal places.)Your answer4 pointsDetermine the required torque (in N-m) as limited by the angle of twist.(Please DO NOT USE SCIENTIFIC NOTATION in your final answers. Please write final answers to

Answered: Image /qna-images/answer/18859ae9-f222-4ca3-814d-48dbd967310c.jpg

A steel shaft with a diameter 45 mm and length 1.30 m transmits 55.50 kW from an electric motor to a compressor. The allowable shear stress is 51.75 MPa and the allowable angle of twist is 2.1 degrees. G=83 x 10^3 psi Determine the polar moment of inertia (in mm^4) of the steel shaft. * 3 points (Please DO NOT USE SCIENTIFIC NOTATION in your final answers. Please write final answers to 4 decimal places.) Your answer 4 points Determine the required torque (in N-m) as limited by stress. * (Please DO NOT USE SCIENTIFIC NOTATION in your final answers. Please write final answers to 4 decimal places.) Your answer 4 points Determine the required torque (in N-m) as limited by the angle of twist. (Please DO NOT USE SCIENTIFIC NOTATION in your final answers. Please write final answers to

A steel shaft with a diameter 45 mm and length 1.30 m transmits 55.50 kW from an electric motor to a compressor. The allowable shear stress is 51.75 MPa and the allowable angle of twist is 2.1 degrees. G=83 x 10^3 psi Determine the polar moment of inertia (in mm^4) of the steel shaft. * 3 points (Please DO NOT USE SCIENTIFIC NOTATION in your final answers. Please write final answers to 4 decimal places.) Your answer 4 points Determine the required torque (in N-m) as limited by stress. * (Please DO NOT USE SCIENTIFIC NOTATION in your final answers. Please write final answers to 4 decimal places.) Your answer 4 points Determine the required torque (in N-m) as limited by the angle of twist. (Please DO NOT USE SCIENTIFIC NOTATION in your final answers. Please write final answers to

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Assignment 6 The shaft in Figure consists of a (3 in) diameter aluminum segment that is rigidly joined to a (2 in) diameter steel segment. The ends of the shaft are attached to rigid supports, Calculate the maximum shear stress developed in each segment when the torque (T = 10kip in) is applied. Use G = 4x10 psi for aluminum and G = 12x10 psi for steel. Aluminum Steel 3-in. diameter 2 in. diameter
90°–0 9. A A metal [E = 106 GPa; v = 0.31] bar of height h = 40 mm and thickness t = 8 mm is subjected to an axial load P. Two strain gages mounted at point A measure strains of ɛx = 575 µɛ and ɛy = -10 µɛ; however, the angle 0 indicated in the figure is not known. What is the magnitude of load P? Ex + Ɛy' : i με Ex + Ɛy = i Ox = i MPa P = i kN
Determine the largest torque T which may be applied to end of the solid bar which is shown in the diagram below, knowing that the maximum allowable shear stress = 107MPa and G = 40GPa. Provide your answer in kNm with precision to two decimal points. B 40 mm TABLE 3.1. Coefficients for Rectangular Bars in Torsion a/b C₁ C₂ 1.0 0.208 0.1406 1.2 0.219 0.1661 60 mm 1.5 0.231 0.1958 2.0 0.246 0.229 2.5 0.258 0.249 3.0 0.267 0.263 4.0 0.282 0.281 5.0 0.291 0.291 N 10.0 0.312 0.312 مة 0.333 0.333
For the beam shown, calculate the bending stress at a point 70 mm. from the top of the beam. P = 59, a = 233, b = 296 Round your answers to 2 decimal places.
Three steel rods, each having a cross-sectional area of 500 mm2, are assembled in a symmetrical manner, ass shown in the igure. Assume that steek behaves as a linear elastic material with E= 200 GPa. Determine the deflection of joint A due to a downward force of P= 2MN
2 decimal places
A beam having the cross section shown is subjected to a couple that acts in a horizontal plane. Determine the largest permissible value of the moment Mo of the couple if the maximum stress in the beam is not to exceed 13 ksi. Given: ly=/z=11.3 in 4 A=4.75 in² kmin = 0.983 in. 0.5 in. 1.43 in.- Mo C B 0.5 in. ✓ 5 in.- 1.43 in. The largest permissible value of the moment Mo is kip-in. 5 in.
Help please!
PLEASE MAKE THE SOLUTION COMPLETE, UNDERSTANDABLE AND READABLE. Please write the solution in the paper.
The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m. Before the load is applied, the beam hangs level. Use E 200, 000MPa and a = 11.7- m C" Neglect bending of the beam. A=640mm2 A=320mm2 A C D 1.2m 0.8 m 1.2 m 54KN What is the stress of rod B if there is no change in temperature in MPa?
Solve the Problem, Thanks
From the figure as shown, the maximum shearing stress is 30 MPa and the angle of twist is 1.35°. Determine the maximum permissible torque? Use G = 90 GPa and use 2 decimal places. 50 тm O 48 тm O T A В C 1.25 m 1.40 т