A steel plate is hoisted by a cable sling that has clevis at each end as shown in the Fig.1. The total weight of the plate is 100 kN. The pins through the clevises are 20 mm in diameter. The cable has diameter of 25 mm. Each half of the cable is at an angle of 35° to the vertical. Using factors of safety of 2 for normal stress and 3 for sheer stress, check if the mechanical system is safe. ofrail.cable = 250 MPa and Trait.pin = 100 MPa

A steel plate is hoisted by a cable sling that has clevis at each end as shown in the Fig.1. The total weight of the plate is 100 kN. The pins through the clevises are 20 mm in diameter. The cable has diameter of 25 mm. Each half of the cable is at an angle of 35° to the vertical. Using factors of safety of 2 for normal stress and 3 for sheer stress, check if the mechanical system is safe. ofrail.cable = 250 MPa and Trait.pin = 100 MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

compute the forces in all members and the stresses in the midsection, away from any joint. Refer to the Appendix for the cross-sectional area of the members indicated in the figures. Consider all joints to be pinned.
Machine Elements. Factor of safety 1.5 , double pin , hollow square bar .
The one end of a hollow square bar whose side is 10 in with 1 in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and Oall 243 ksi for pin material.
10000 lb is applied at G, pin C can have 5000 max horizontal load and 6000 vertical load, determine max angle of bed
6.10 - This is a statics problem that deals with ‘Zero-Force Members’.
The one end of a hollow square bar whose side is 10.42 in with 1.42 in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a pin. Find the minimum diameter of pin is used. Take oall = 243 ksi for pin material.
4. The bar below is subjected to an axial load of P. The safety factor against compressive failure is 1.5. Find the allowable load in KIPS if the material is cast iron. Sin 2in 1 ft
Why is is that when I compute for the diameter, the answer is 7.9706? How was 13.22 obtained? Bartleby link for solution: https://www.bartleby.com/questions-and-answers/a-steel-rod-is-stretched-between-two-rigid-walls-and-carries-a-tensile-load-of-5000-n-at-20c.-if-the/5c99ed3b-d083-41be-a905-b15aa3bc8648
Kindly show your complete handwritten solution. Answers in mm.
2. Two initially rigid bars AC and DG are pinned at A and G and are also connected by vertical bars BD and CF, each having rigidity = AE. The temperature of bar BD is then raised by an amount AT. 1.5L B D F -2L- Address the following: a. Draw accurate and complete FBD of AC, DG, BD, CF b. Which of a. are two-force members? c. Compute the force in BD in terms of a, AT, AE d. Compute the force in CE in terms of a,AT, AE
The one end of a hollow square bar whose side is 10.50 in with 1.50 in thickness is under a tensile stress and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and σallowable=243 ksi for pin material.