A spherical buoy is moored to a river bed. The riverflows from left to right. Because of flow, the line thatties the buoy is tilted 5° from the upright position, asshown in the graph to the right. At this location the topsurface of the buoy is just below the water surface.The effective specific gravity of the buoy is 0.65. Thediameter of the buoy is 2 ft and the line is 4 ft inlength. What is the force acting on the line? What isthe horizontal force acting on the buoy that comesfrom the flow?SurfaceFlow85°

Answered: Image /qna-images/answer/c5e7a4d8-95f5-4a01-a9ae-c10b4f3e8986.jpg

Answered: A spherical buoy is moored to a river…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

is required to open the gate A-B? The density of water is 1000 kg/m3 and the density of the block is 8000 kg/m3. The What is the minimum Block mass (kg) that the gate is not required. The external force that effects the gate at point A is Fe=3000 specific gravity of oil is 0.9. The depth of N, while the hydrostatic force Fh=5084.4 N. 1 m Fe rope 4 m Oil Fh 1.2 m 30 Block Water
The tank shown is 1.5 m wide into the paper. Determine the: A. Maximum value of ax without spilling any water and the corresponding force on the rear side wall AB. B. The minimum value of ax if the pressure at C is 0. C. The value of ay if ax=4.5 m/s2 and the pressure at C is just zero. 0.4m 0.8 m 0.75 m 1.8 m a₂
The vessel shown below contains linseed oil at 77° F. One side of the vessel contains a spout which is sealed with a 12-inch diameter flat circular gate hinged along its top edge. The horizontal axis of the hinge is located 6 feet below the water's surface. Determine the minimum required torque (moment) on the hinge to hold the gate shut. Neglect the weight of the gate and friction in the hinge. 6 feet Hinge 12-inch dia. gate Linseed oil
A tank 13 ft deep and 5 ft wide is layered with 6 ft of oil (γ = 50.0 lbf/ft3 ), 5 ft of water, and 2 ft of mercury (γ = 846 lbf/ft3 ). Compute (a) the total hydrostatic force and (b) the resultant center of pressure of the fluid on the right-hand side of the tank.
Hello! Can you please assist me in solving these questions. Thank you in advance
2. Cylindirical cup below is open at its top and totally filled with water. It is rotated with a contant angular velocity = 36.5 rad/s. Calculate volume and depth of water retained in the cup after this rotation. Hint: Volume of paraboloid is equal to the half volume of a cylinder with the same height. 0.4 m 0 0.08 m M X @₂=0
The diameter of droplet is 0.075 mm. What is the intensity of the pressure (N/sq. cm) developed in the droplet by surface tension of 0.000075 N/mm?
Using the figure depicted below, calculate the minimum height h at which cavitation begins to occur. Indicate on the figure where the cavitation occurs. Be sure to state all assumptions. Note that section 2 opens to atmosphere. D = 5 cm D2 = 8 cm Open jet Water at 30°C D
A cylinder with a diameter of 0.5 m and a height of 1.8 m is shown below. The water flows through a flap valve (attached to the pair) with an opening of 0.075 m in diameter. It must be pushed up to open the valve. Determine the force to open the valve.
Use density of water = 1000kg/m^3 and acceleration due to gravity equal to 9.81m/s^2. A rectangular tank containing water at a depth of 1.2m is accelerating towards the right, the motion of which is parallel to the longest side. If the tank has the following dimensions: length = 3 meters, width = 1.8 meters, and height = 1.5 meters, determine the following: the maximum allowable acceleration (m/s^2) of the tank; and the unbalanced force causing the maximum acceleration in kN. angle (in degrees) of fluid inclination of the acceleration from part a. how many cu.m of water is spilled when a = 2.5m/s^2. Note: Do not include units in your answers. Do not round off intermediate values and answer in four decimal places.
Fluid with a density of 1200 kg/m^3 is applying pressure on the gate shown. The depth of the water is equal to the height of the gate. The h is 6 m and width of the gate is 3 m. Determine the resultant pressure force acting on the gate? fluid gate 35305 N 847325 N 70610 N 1271000 N 635494 N
Calculate the X value since the specific gravity of the square prism-shaped object shown in the figure with a base edge a= 65 cm is γ = 0.94 t/m3, the specific gravity of the oil is γy= 0.77 t/m3.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS