A solid circular column with 40 mm diameter is to be replaced by a hollow circular section of the same material. The cross sections of solid and hollow circular are shown in Figure Q4(b). Find the size of the hollow section if the internal diameter is 0.5 times the external

A solid circular column with 40 mm diameter is to be replaced by a hollow circular section of the same material. The cross sections of solid and hollow circular are shown in Figure Q4(b). Find the size of the hollow section if the internal diameter is 0.5 times the external

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The figure shows a cutaway view of an assembly in which a solid bronze [G= 6,500 ksi] rod (1) is fitted inside of an aluminum alloy [G = 4,000 ksi] tube (2). The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at A. The rod diameter is d₁ = 1.55 in. The outside diameter of the tube is D₂ = 2.8 in. and its wall thickness is t₂ = 0.115 in. Overall dimensions of the assembly are a = 35 in. and b = 11 in. The allowable shear stresses for the bronze and aluminum materials are 9800 psi and 8500 psi, respectively. Further, the rotation angle of end B must be limited to a magnitude of 4.2°. Based on these constraints, what is the maximum torque Tg that can be applied at end B? Fixed End plate plate di TB Rod (1) D₂ Answer: TB = A Tube (2) a lb-in b B
Shown in the figure attached is a beam. Given the loading and support condition and assuming that EI is constant for the beam, determine the (a) The equation of the elastic curve, (b) The deflection at the left end of the beam, and (c) The support reactions By and MB.
In the figure shown, the rigid beam with negligible mass was horizontal before the load P was applied. Determine the value of load P if the vertical movement at P is 3mm. Draw the FBD and deformation diagram.
1) The head H is connected to the cylinder of a compressor using six steel bolts. If the clamping force in each bolt is 4000N, determine the normal strain in the bolts. Each bolt has a diameter of 5 mm. If o₂ = 280 MPa and Est = 210GPa, what is the strain in each bolt when the nut is unscrewed so that the clamping force is released? a) 0.970 b) 0.203 c) 0.970(10-³) d) Insufficient information to determine because the stress is beyond yield point H &
2. A linear spring of stiffness k N/mm is to be designed to stop a railroad car, with a mass of m kg, traveling at v, km/hr within x mm after impact. Find the smallest value of k, in terms of m, ve, and x, that will produce the desired result. Hint: a dx = v dv. mim Vo k wwwM
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. The cross-sectional area of the bronze, aluminum, and steel are 448 mm2, 622 mm2 , and 265 mm2 respectively.Determine the change in length (in mm) of the bar if P = 27199 N.The moduli of elasticity are 81.82 GPa for bronze ,73.92 GPafor aluminum , and 204.55 GPa for steel .
A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between them which is 699.93 mm long. If the allowable stresses are Salum = 90 MPa and Spronze=80 MPa, find the maximum weight of the beam that the system can support (in KN). note: please help us in this sample question and it is not a graded question but a practice question thank you
Bar ABC is rigid and rotates freely about B. The loads consist of a point load and a uniform temperature change in both bars CD and EF. Determine the temperature change (AT) at which points A and E first come into contact. Report your answer rounded to the nearest degree. 100 in initial gap = 0.11 in F T E A = 2.0 in² AEF EEF = 12,000 ksi aEF LEF 100 in = 13.5 x 10-6 1/°F = 50 in B 14 k 100 in D с ACD= 1.5 in² ECD CD= 6.5 x 10-6 1/°F = 29,000 ksi = 150 in LCD Y Z
Please solve it within 30 minutes please i need help formulas are also attached
Provide solution and explain also with steps
Consider a composite shaft of steel and aluminium having length L and fixed at one of the ends as shown in figure. Steel O Al 1.5 d t The hollow shaft of steel has outer diameter as 1.5 d and inner diameter as d, while the solid shaft of aluminium has the diameter as d. If the composite shaft is subjected to torque, T then the torque resisted by steel shaft is % (rounded off to one decimal place) of the applied torque. Assume modulus of rigidity of aluminium is one third of modulus of rigidity of steel. [Take G₁ = 3 GAL]
Determine the polar moment of inertia for brass sleeve and steel shaft.