Current Attempt in ProgressA soccer ball with an inside diameter of 118 mm is inflated to a gage pressure of 110 kPa. The ball is constructed from a polymer [E =50 GPa; v = 0.35] that has a yield strength of 25 MPa. If a factor of safety of 3.0 with respect to the yield strength is required,determine the minimum wall thickness required for the ball.O 0.499 mmO 0.389 mmO 0.541 mmO 0.322 mmO 0.419 mm

Given Pressure, P = 110 kPa Factor of safety, f = 3 Yield strength, Y = 25…

Answered: A soccer ball with an inside diameter…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a hydraulic press a 690-liter volume of oil is subjected to a 6666-psi pressure increase. If the compressibility of oil is 2.0×10−5/atm,, find the bulk strain and the absolute decrease in the volume of oil when the press is operating.
"ll zain 1Q ۲۸ مارس، ۲۰۲۱ -> docs.google.com/forms/d/e Q3/ A compound bar is held between two supports as shown in figure 2. If the temperature of the bar is raised from 25°C to 75°C, find the stresses induced in each rod by assuming (a) if the supports do not yield and (b) if the supports yield by 0.25 mm. Take E1= 200 kN/mm2, E2 = 30 kN/mm2, E3 = 100 kN/mm2, And, a1= 1.2 x 10-5/°C, a2= 1.8 x 10-5/°C d3= 1.6 x 10-5/°C Q3/ * 0= 150 mm 0= 100 mm 0= 50 mm Figure 2 200 mm 300 mm 500 mm (1) 01= 194.78 N/mm2, a2= 48.7 N/mm2, 03= 21.64 N/mm2/(2) 01= 133.14 N/mm2, 02 33.28 N/mm2, a3= 14.79 N/mm2 (1) 01- 184 3anm2, 92- 44.73 N/mm2. 03- 24.64 N/min2/ (2) a1 143.14 N/mm2 o2 36 21 N/mm2, 03-14.79 N/mm2 (1) a1- 190.28 N/mm2, 02 48.26 N/mm2,
Determine the bulk modulus for each of the following materials: (a) rubber, Er = 0.4 ksi, nr = 0.48, and (b) glass, Eg = 8(103) ksi, ng = 0.24.
A cylinder has an internal diameter of 230 mm, has walls 5 mm thick and is 1 m long. It is found to change in internal volume by 12.0 × 10-6 m³ when filled with a liquid at a pressure p. If E=200 GN/m² and v = 0.25, and assuming rigid end plates, determine: (a) the values of hoop and longitudinal stresses; (b) the modifications to these values if joint efficiencies of 45% (hoop) and 85% (longitudinal) are assumed; (c) the necessary change in pressure p to produce a further increase in internal volume of 15%. The liquid may be assumed incompressible.
modulus of elasticity equal to 200x103 MPa and coefficient of thermal expansion equal to 11.7x10^-6/°C, the bottom is made up of brass with modulus of elasticity equal to 105x10^3 MPa coefficient of thermal expansion equal to 20.9x10^-6/°C. The temperature rose to 50°C from normal condition introducing stresses in the bar. Determine the force induced in the bar. T 250 530 mmm r so mm 300 mms
Mechanical engineering. A steel beam is installed in a building when the ambient temperature is -12C. If the beam if fixed at it's ends (prevented from expanding/contracting), calculate the stress that will develop in the beam if the ambient temperature rises to +32C. State whether the stress is tension or compression. Assume E 200,000 MPa and \alpha L = 12x10-6 (/\deg C)
A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v = 0.33] pipe has an outside diameter of 245 mm, a wall thickness of 15 mm, and a length of 4.5 m. The pipe supports a compressive load of 610 kN. After the temperature of the pipe drops 49°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) 8 = i AD= i mm mm
A spherical pressure vessel has an inside diameter of 4 m and a wall thickness of 15 mm. The vessel will be constructed from structural steel [E = 200 GPa; v = 0.29] that has a yield strength of 203 MPa. If the internal pressure in the vessel is 1930 kPa, determine the factor of safety with respect to the yield strength. 1.58 2.21 O 1.30 1.45 O 1.13
A polymer cylinder (2) is clamped between rigid heads by two steel bolts (1). The steel [E - 29,000 ksi; a - 6.5x10-6/°F] bolts have a diameter of 0.45 in. The polymer [E - 370 ksi; a - 39.9x 10-6/°F] cylinder has an outside diameter of 6.2 in. and awall thickness of 0.35 in. Assume a - 27 in. and b - 35 in. If the temperature of this assembly changes by AT - 145°F, determine: (2) the normal stress in the polymer cylinder. (b) the normal strain in the polymer cylinder. (c) the normal strain in the steel bolts. (1) (2) (1) Answer: (a) 02 - psi. (b) E2 - (c) E1 - με
answer as soon as possible
5. In the CN Railwayproject,steel railroad rails of 9.5meters long are to be installed.If the modulus of elasticity of steel is207GPa, and if the lowest temperature considered is 18°C and a maximum temperature of 36°C is designed for, determine the clearance between the rails such that adjoining will just touch at maximum design temperature. Assume α for steel is 11.6 x 10-6/°C
A 5-m rod having a uniform cross-sectional area of 1000 sq. mm. is secured between two walls5 meters apart. The load on the rod is zero at 27 °C. E = 200 GPa, α = 11.25x10-6 m/m-°C. Whenthe temperature rises to 57°C: What is the stress in the rod assuming that the walls are rigid and stress (in the rod) if the walls spring together with a total distance of 0.5 mm? pls box final answer

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS