A simply supported beam of length '2L' carries a uniformly distributed load of 2w per unit length over the entire span. It is supported at the mid span of beam by a spring and force developed in spring is one third of the total load on the beam. What will the spring constant of the spring? 2w per unit length 000

A simply supported beam of length '2L' carries a uniformly distributed load of 2w per unit length over the entire span. It is supported at the mid span of beam by a spring and force developed in spring is one third of the total load on the beam. What will the spring constant of the spring? 2w per unit length 000

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Draw up the diagrams of internal forces N, V and M of the following loads.
3. The tow truck’s front wheel will be lifted off the ground if the moment of the load W about the rear axle exceeds the moment of the 6200-lb weight of the truck. Determine the largest Wthat may be safely carried by the tow truck.
A steel column of rectangular section 10 mm * 5mm and length 0.5 m is simply supported at both ends. Assuming modulus of elasticity, E=200GPa for steel. Calculate the critical axial load ?
Incorrect Question 2 Using the Equilibrium equations calculate Reaction Ay for the truss shown below, if all noted dimensions are 12 feet. Round to the nearest hundreth of a Pound. (# # #.# # Lbs.) 900 lb. 600 lb. C 12 ft. D LA 12 ft. A duda 803.87 12 ft. E 12 ft. 200 lb. 12 ft. B 701010 299 5
i need the answer quickly
The rigid beam is supported by a pin at C and an A-36 steel guy wire AB. Part A 10 ft 30° If the wire has a diameter of 0.3 in., determine how much it stretches when a distributed load of 150 lb/ft acts on the beam. The material remains elastic. Express your answer to three significant figures and include appropriate units.
A beam is supported as shown below: В C D E F Hinge Hinge 米 5 m 5 m 6 m 3 m 3 m The beam is to carry the following loads, in (kN) and in (kN/m), in the table below: LOAD w(DL) W(LL) P(LL) SET 1 (1,2,3,4,5) SET 2 (6,7,8,9,0) 20 25 40 30 15 50 Using influence line diagrams, determine the following: 2. Maximum reaction at F, RF in kN.'
A wide flange section for a 6 m long column (hinged at both ends)has the following properties:Cross-sectional area = 8,500 mm2Radius of gyration, ?? = 100 mmRadius of gyration, ?? = 50 mmModulus of elasticity, ? = 200 GPaDetermine the Euler critical load of the column.
A garbage truck weighs 152 kN 20 m bridge girder, as shown in Figure 3. The total weight of the truck will be disuributed 38% in the passes through a front wheel while the remaining weights will be distributed at the rear wheel. If the wheels are 4 m apart from each other, determine the maximum moment applied in the bridge girder and only consider two locations of loads: one for front and the other one for rear, from the total weight of the garbage truck. Figure 3 A garbagTe truck nasses through the bridge girder
I'm having a diffucult time understanding the loads and reactive forces problem 1.7. How did the distributed load for I2 = 3ft and I3= 1 ft where did they get 3ft and 1 ft. I understand how they got I1= 7ft with a beam spaning 14 ft divide 2 = 7ft. I need an explanation on how and why I2 = 3ft and I3= 1 ft?
and what is the value of P in lbs