A simply supported beam of grade 350W spanning 10m is made from 305×102×33 I section. It is laterally supported at mid length and its ends only. Find the maximum point load the beam can carry if it is placed 3m away from support A.

A simply supported beam of grade 350W spanning 10m is made from 305×102×33 I section. It is laterally supported at mid length and its ends only. Find the maximum point load the beam can carry if it is placed 3m away from support A.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Determine the flexural capacity of a W24 x 62 section to be used as a cantilever beam to IS carry…

A: The values and diagram given in the question are as follows Beam section W24x62 fy=345 MPa

Q: Beams A beam 300 mm depth and of symmetrical I section has a l = 1 x 108 mm4 and is simply supported…

A: Given- Beam depth d=300 mm, Symmetrical I-section- I=1×108 mm4, Span L=6 m, Maximum Bending stress…

Q: SITUATION: A simply supported beam having a span of 12m carries a uniform dead load of 7.3kN/m and a…

A: Span of the supported beam: 12 mUniform dead load: 5.8 kN/mLive load: 8.8 kN/mConcentrated dead load…

Q: A T-beam that traverses the center of a floor system for which bw = 300mm and d=550 mmm. The beams…

Q: A simply supPorted steel joist with a 4.0 m effective span <arries a uniformly distributed Ioad of…

Q: moment 1. Determine the maximum bending of the beam. 2 Determine the actual bending stress. 3.…

Q: Determine the location from the midspan in meters where stirrups are no longer required.

A: The values given in the question are as follows: Width of the beam(b)=300 mm The total depth of…

Q: # 3: Analyze the beam 6 kN 1 kN/m 3 KN shown in beam below and draw the bending moment and shear…

A: The loads acting on beam are given . Note According to the company rules i am able to answer first…

Q: Distributed Loads Replace the loading on the beam shown with an equivalent resultant force and…

A: Equivalent resultant force Ry=12×2.5×5 + 1.2×2 + 12×2.5-1.2×2 + 1.2×3 +6…

Q: which among these failure modes in LTB govern?

A: Please don't put same question again and again.

Q: 2 A rectangular beam having b=12 in. and d=22 in. spans 30 ft face-to-face of simple supports: It is…

Q: A rectangular beam is 300 mm x 550 mm and is reinforced with 2- 28 mm top bars and 3-28 mm bottom…

A: Given data:- Cross-section of rectangular beam is 300 mm × 550 mm Diameter of reinforcement, d=28 mm…

Q: If the allowable bending stress is 124.66 MPa, compute the safe concentrated load that it could…

A: w=40 kN/mfy=248 MPaL=14 m

Q: A prismatic beam having 275mm x 500 mm is reinforced for flexure at the bottom with 5- phi 20 mm…

A: Given data:- Cross sectional area of beam is 275mm×500mm Effective depth, d=420 mm Uniformly…

Q: For the continuous beam shown, determine the plastic moment capacity. L1 = 6 m, L2 = 3 m, L3 = 3 m,…

Q: A simple beam of length L- 5 m carries a uniform load of intensity = 5.8 kN/m and a concentrated…

A: Given Data A simply supported beam is given with the following data Span length is 5 m A uniformly…

Q: Assignment No. 01 A simply supported deep beam has a clear span equal to 3660 mm, a total height…

A: The span-to-depth ratio for the beam is 3, thereby qualifying it as a deep beam. A strut-and-tie…

Q: A steel column carries an axial load of 801 kN and a moment of 71 kN-m at the top and moment at the…

A: A steel column carries an axial load of 801 kN and a moment of 71 kN-m at the top and moment at the…

Q: A simply supported steel joist with a 4.0 m effective span carries a uniformly distributed Ioad of…

Q: A horizontal steel girder of uniform section, 15 m long, is supported at its extremities and carries…

A: From the above information, we have find the deflection under the loads for this we need to follow…

Q: 3 in. in. 2 in. i in. 2 in. i in. Prob. 9-66

A: The location y¯ of the Centroid for a beam having the cross section area is shown. The beam is…

Q: А %3D 400 kN В 3 280 kN A В -2.4 m -7.4 m -1.2 m-

A: Draw FBD:

Q: A reinforced concrete one slab is built integrally surrounding with its supports (beam size is 200mm…

Q: : An 2.44 m span cantilever beam has a rectangular section and reinforcement as shown in Figure. The…

A: Introduction- The cantilever is a stiff structural member which stretches horizontal but is only…

Q: A W 21 x 93 A36 steel is used for a cantilever beam with a span of 5.0m PROPERTIES OF W 14 x 132 A =…

A: Given: Span, L = 5 m A36 steel: fy = 250 MPa fu = 414 MPa Properties of the section W14x132: A =…

Q: A rectangular beam has b=300mm and d=520mm. Determine As(max) if fc'=27.5MPa and fy=415MPa. Use 2015…

Q: Beam and girder simplified analysis- FBD analysis including reactions. B2,B3,G2,G3. 100 psf total…

Q: An existing beam shown carries an 8-ft high wall. It will be renovated and be replaced with the ff…

A: To find:The load that the beam will carry in kN/m

Q: Prob. #1: Determine the allowable concentrated load @ midspan that may be applied to a W530 X 84.8…

A: Allowable Concentrated load: It is defined as the maximum point load which is allowed for safe…

Q: Problem 1 A T-beam has the following properties: base of the flange = 800 mm base of the web = 300…

Q: A 3.5m cantilever beam is carrying a uniformly distributed factored load of 10.9 kN/m including its…

A: Given : 3.5 m cantilever beam W21X48 section Factored load, Wu = 10.9 kN/m A36 steel , ASD and LRFD…

Q: Determine the design flexural strength in ft kips of a W10X26 of A242 (Fy = 50ksi) steel subject to…

Q: An 2m. long beam is on hinged at its left end and on fixed support at its right end. Its flexural…

A: Given data Length of beam (L) = 2m Flexural capacity (Mmax ) = 610 KNm Shear capacity (Vmax ) =…

Q: concrete 1-beam has an effective depth of 620mm and is reinforced with 8D28mm dia. Bars. The web…

Q: A W 5300*101 of Steel Section (fy= 345 MPa & fu= 450 MPa) is used as simply supported beam with a…

A: Given- A W 5300×101 Steel Section with a span of 15 m is used as simply supported beam. In addition…

Q: Design a simply supported beam that will carry an ultimate load of 1750 kN-m. The beam is a W…

A: Given Ultimate moment 1750knm Fy = 345 mpa LRFD METHOD

Q: A concrete beam has a cross sectional area of 275mm width and 150mm height for the upper flange.…

Q: 19. What is the available shear strength of the W24x68, ASTM A992 beam, if d 23.7 in G=0.415 in A)…

Q: A rectangular beam has a width of 300mm and effective depth of 440mm. It is reinforced with 3-32…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Need some help with the question
A steel column carries an axial load of 801 kN and a moment of 71 kN-m at the top and moment at the bottom which is only70% of the moment at thetop. The two moments are in opposite direction and applied about the x-axis and the steel section has the following properties:A = 13159 mm2ry = 109 mmry = 94 mmSx = 1200 x 103 mm3K= 1.0L= 3.6 mE= 200,000 MpaFy = 248 MpaUse NSCP specification for compressive stress and Fb =148 Mpa.Determine the Allowable Compressive Stress.
Considering the frame, the height of each storey is 5 m (DA) and 4m (DG) , the length of each span is 6 m (GH) and 7 m (HI), assuming columns and beams have the same cross sectional areas. *Using the cantilever method, what is the axial force at column FC?
. A beam is constructed from a reinforced 50mm x 200mm section of timber using two L120x80x12 steel angle sections. Considering that the effort allowable stress in wood is 10 MPa, and the allowable stress in steel is 110 MPa. Determine the maximum positive and negative moment that the beam can support
Considering the frame, the height of each storey is 5 m (DA) and 4m (DG) , the length of each span is 6 m (GH) and 7 m (HI), assuming columns and beams have the same cross sectional areas. *Using portal method, what is the axial force at column FC?
ASAP NEED RIGHT COMPLETE SOLUTION !!!
l8
Q.2 If the (010×10) cylinder compressive strength of O.P.C. concrete at 10-day is (14 MPa). Calculate (20×20×20) cube comp. strength at age of 28 days.
Solution and figure please
Plss, i need the answer immediately. Consider a two-bay building frame ABCDEF, with A, B, and C as fixed supports, AD, BE, and CF as columns, and DE and EF as girders. Span DE is 5.9 meters long and span EF is 6.8 meters long. The columns have a height of 10.5 meters. Assume that the columns have same cross-sections. A wind-induced lateral load of 80 kN is applied at D, pointing towards the structure. Additionally, a-wind induced uniform load of 1.5 kN/m, pointing upwards, is applied at the girders. (a) Draw the free-body diagram of the structure.
AW 21 x 93 A36 steel is used for a cantilever beam with a span of 5.0m PROPERTIES OF W 14 x 132 A = 17 600 mm? , = 862 x10 mm d = 549 mm 4 = 38.7 x10 mm tw = 14.7 mm bị = 214 mm t, = 23.6 mm The beam is used to carry a distributed dead load of 60kN/m and a distributed live load of 75KN/m A. Determine the shear flow at neutral axis. B. Determine the allowable shear capacity of the section using ASD NSCP 2001 C. Determine the design shear capacity of the section using LRFD NSCP 2015