Q2)A shaft rotating at 350 r.p.m. drives another shaft at 550 r.p.m. and transmits 10.5 kWthrough a belt. The belt is 80 mm wide and 9.5 mm thick. The distance between the shaftsis 3.8 m. The smaller pulley is 9 cm in diameter. Calculate the stress in the belt, if it isacross belt drive. Take u = 0.3.2. (30 degrees)Q3

Answered: Image /qna-images/answer/5cf7d962-9afc-44ae-9241-7362ff0a812b.jpg

A shaft rotating at 350 r.p.m. drives another shaft at 550 r.p.m. and transmits 10.5 kW hrough a belt. The belt is 80 mm wide and 9.5 mm thick. The distance between the shafts s 3.8 m. The smaller pulley is 9 cm in diameter. Calculate the stress in the belt, if it is cross belt drive. Take u = 0.3.2. (30 degrees)

A shaft rotating at 350 r.p.m. drives another shaft at 550 r.p.m. and transmits 10.5 kW hrough a belt. The belt is 80 mm wide and 9.5 mm thick. The distance between the shafts s 3.8 m. The smaller pulley is 9 cm in diameter. Calculate the stress in the belt, if it is cross belt drive. Take u = 0.3.2. (30 degrees)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A motor driving a solid circular steel shaft transmits 40kW of power at 500 rpm. If the diameter of the shaft is 40 mm, the maximum shear stress in the shaft is MPа.
A motor transmits 180 hp to the driving pulley, in the figure assuming that A takes 40 hp and C takes 140 hp, design the shaft for an allowable shear stress of 8000 lb/in2, the speed is 630 rpm
A shaft is used to transmit 67 kw at a speed of 2,281 rev/min. Using a maximum allowable shear stress of 57 MPa, find the shaft diameter in mm.
(BB) Q1: The shaft, as shown in Fig. is driven by pulley B from an electric motor. Another belt drive from pulley A is running a compressor. The belt tensions for pulley A are 1500 N and 600 N. The ratio of belt tensions for pulley B is 2.5. The diameter of pulley A is 150 mm and the diameter of pulley B is 480 mm. The allowable shear stress for the shaft material is 85 MPa. Taking torsion and bending factors as 1.25 and 1.5 respectively, find the shaft diameter. C # -100- A B -150-100 D TB2 All dimensions in mm. B A TAZ TAI TB1
A shaft of diameter d is guided in rotation at A (bearing 1) and C (bearing 2) and carries two wheels supporting the indicated loads, The radius of wheel B is 200 mm, and of wheel D is 100mm. The shaft is made of steel. F2 = 6000 N. Dimensions are in mm. Calculate the diameter (mm) of the shaft considering an allowable stress of 270 MPa for a stress composed of bending and torsion.
The drive shaft for a truck (outer diameter 60 mm and inner diameter 40 mm) is running at 43 Hz. If the shaft transmits 156 kW, what is the maximum shear stress in the shaft in MPa?
A Solid shaft transmits 600 N.m torque. If the maximum shear stress induced in the shaft is 50 N/mm2, the minimum diameter of the shaft is
a shaft 80mm diameter transmits power at maximum shear stress of 63 mpa. find the length of 20mm wide key required to mount a pulley on the shaft so that the stress in the key does not exceed 42 mpa.
I need the answer quickly
A solid shaft made from AISI 1040 cold-drawn steel is used to carry two V-belt, as shown in the Fig. 3. Pulley A receives power from a motor through a belt, with the belt tensions shown in Fig. 3. The power is transmitted through the shaft and delivered to the belt through pulley B. Assume the belt tension on the loose side is 10 percent of the tension on the tight side.
A drilling riser is used to drill a 4km deep hole into the seabed. The riser can be approximated as a hollow steel shaft of 185mm and 160mm outer and inner diameter respectively. If the power exerted is 230kW and the speed of rotation of the drill is 75RPM, calculate the maximum shear stress in the shaft and the twist of one end relative to the other in degrees.(Note the angle of twist of a 4km drill string is going to be >> 360o ) G = 89 kN/mm2
A shaft under the torsion has a pure shear stress on the surface. What is the maximum principal stress on the surface which is at 45° to the axis?