A shaft has a number of collars integral with it. The external diameter of the collars is 40omm and the shaft diameter is 250 mm. If the intensity of pressure is o.35N/mm² (uniform) and the coefficient of friction is o.05. Estimate: 1. power absorbed when the shaft runs at 105 r.p.m Carrying a load of 150 KN; and 2. number of Collars required

Q: Determine the Resultanto f the eoplanar orcesestem

A:

Q: what is 6 to 10 po?

A:

Q: resolve solution

A:

Q: S0ON so

A:

Q: Q1 (a) During construction of a highway bridge, the main girders as shown in Figure Q1(a) are…

A: The maximum bending stress in a girder due to this load is 85 MPa.

Q: 10 kNim 50 kN Identify the moment diagram of the beam shown. 3125 3125 (AN mA 022 (AN-m)A

A:

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

A:

Q: Answer in number 7 and 8.

A:

Q: can you answer 1B

A:

Q: Draw the box closing mechanism given in the figure in the given dimensions. Determine the velocities…

A:

Q: A plane's propeller can be modeled as a thin, uniform rod that rotates about its frictionless center…

A: Given data  F = 591 N  L = 6.51  m  mass of propeller (m) = 10.1 kg    To determine  (a) direction…

Q: You are designing a new engine; this device operates with liquid fuel as an input and gener energy…

A: Hello. Since you have posted multiple questions we will solve the first question for you. If you…

Q: Q.2 A cantilever beam of length / = 5 m, flexural rigidity El in MPa, and mass m = 1950 kg carries…

A:

Q: both answers are wrong :(

A: Given DataT1=310KP1=320kPaM1=0.3 To findV2=?P2=?

Q: Add the length of all the horizontal pieces. They go left and right.

A:

Q: Draw the isometric drawing

A: Isometric projection Isometric projection is a method for representing three-dimensional objects…

Q: how can I get the 85 α

A:

Q: Find this range. Ds i mm

A:

Q: ENTIRE ANSWER IS WRONG

A: Initial velocityFinal velocityInitial angleFinal angleWeight of the basketball

Q: What is the average force magnitude?

A:

Q: For figure (4): The ring is subjected to two forces (F, and F2). Suppose that the resultant force…

A: Given data:

Q: A multi-stage pump, 260 gpm capacity is installed in a well 27 ft below the static water level.…

A: Given data:  The capacity of the pump is given as Q = 260 gpm = 0.579 ft3/sThe total discharge head…

Q: Which of the following statements is FALSE regarding materials experiencing stress within the…

A: Given Stress vs strain plot To write:  WHich statement is false

Q: A piston-cylinder device contains 1.5 kg of steam at 300°C and 0.4 MPa. Steam is cooled at constant…

A:

Q: number d and e?

A: To solve this question, we will use the moment equilibrium equation which is mentioned in the…

Q: A) Are all the nodes in the same plane?. B) To the surface, what would the unit of perpendicular…

A: The 3 dimensional geometric coordinates of the system are taken in uniform units as millimetre. They…

Q: A differential element on the bracket as shown in Figure Q1 is subjected to plane strain that has…

A:

Q: Figure 1 of 1 30 40 F2

A: Given, F1 = 210 N F2 = 510 N Angle between two forces = θ = 40°

Q: The 45° strain rosette is mounted on a surface of the bracket as shown in Figure Q1. The bracket is…

A: Esteel=120 GPaμ=.28 εa=100+60×10-6 εb=-200×10-6εc=-180×10-6 θa=0° ,θb=45°,θc=90°

Q: Through the two pipes in Figure 6 flow equal flows of water. data: Pipe diameter No. 1: 200 mm -…

A:

Q: 7 panels at 4 m B C D 4 m A H. 8 kN 8 kN

A:

Buckling of columns

The column is described as a vertical member of the structure that carries an axial compressive load, and buckling is a lateral deformation of the column under the application of load.