A septic tank is to be constructed to serve for a family of 8 persons. The size of a septic tank is 2300 mm x 1500 mm x 1500mm. Determine the following; a. volume excavated. b. for concreting, compute the cement, sand and gravel (using class A) i. top and bottom slab, ii. footing 6pcs- 0.60mx0.60m x 20cm and iii. column 6pcs- 20cmx20cm

A septic tank is to be constructed to serve for a family of 8 persons. The size of a septic tank is 2300 mm x 1500 mm x 1500mm. Determine the following; a. volume excavated. b. for concreting, compute the cement, sand and gravel (using class A) i. top and bottom slab, ii. footing 6pcs- 0.60mx0.60m x 20cm and iii. column 6pcs- 20cmx20cm

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter18: Pile Foundation

Section: Chapter Questions

Problem 18.13P

See similar textbooks

Similar questions

A soil nail proposed to be installed under the conditions given below is designed against unfactored working force of 50KN. • Ground described as sandy gravel. • Soil nail installed at an angle of 10 degrees to the horizontal and 1.2 m below the ground surface. • Nail dimensions: total length = 5 m with 60% bonded, bonded diameter = 0.35 m, debonded diameter = 0.15 m Assuming parameters not given and considering the water able to be at the surface, propose the suitable type of soil nail and calculate the theoretical working factor of safety of the installed nail against pull out. Also, briefly discuss what would jeopardise your theoretical predictions of the nail performance.
Please show all step
Describe about the Sand-Cone Method in detail.
(BASE ON 100 M LONG) In m3 1. Calculate the Excavate 2. Trench and back fill 3. Disposal of surplus This drawing is not to scale 260 x 500 Grade Beam Cutback slope (HV) 1:1 260 x 150 Void Form. 3 Rows 10M Rebar 000 000 www 900 190 3 Rows 15M Rebar Existing Grade 50 mm Rigid Insulation (200 deep) 300 dia. Concrete Piles (see plan)
1. A precast waterway was shown that uses the principle of tongue and groove for its connection with a uniform thickness of 5cm. Using class "B" mixture, determine the quantity of cement, gravel and sand to be used. 40cm 5cm thickness 225cm long 35cm T&G 27cm 30cm FRONT VIEW REAR VIEW NOTE: SHOW COMPLETE SOLUTION WITH FIGURE
Define sand-cone method.
Q2/ Casing with OD=9.625 in, ID=8.535 in, to be cemented at a depth-13300 ft in 12.25 in borehole. A 40 ft Shoe Joint will be used between float collar and Guide Shoe. It is desired to place 2500 ft of cement in the annulus. Cement Class H, each sack of cement mixed with 4.3 gal of water to which is added 18% salt (hy weight of water).Compute: (1) Slurry density. (2) Slurry yield. (3)Numbe. of sacks of cement reauired. (4) Cementing operation Time. Assume that cement can be mixed 01667 at a rate of 20 sacks/min and displaced at a rate of 9 bbl/min. Use excess of 1.5.
A nign rise bullding wll be bult in a reclalmed area in Metro Manila. Concrete piles will be used as its founcation with detalls ana plans as follows: 0.875m 1.800m 1.800m 1.800m 1.800m 1.800m 1.800m 0.875m 0.875m 1.800m C-1 C-2 1.800m 1.800m 1.800m C-1 C-2 1.800m 1.800m
Describe about the sand-cone method and the rubber-balloon method.
The crushed stone output from a 36-by 42-in. crusher, with a closed opening of 2 ½ in (output is 50 tph)., is passed over a single horizontal vibrating screen with 1 ½ in. openings. If the permissible screen efficiency is 90%, use the information from Peurifoy to determine the minimum-size screen, expressed in square feet, required to handle the output of the crusher. please show complete solution use 4 decimal places
Find the question, thanx.
10m