A reinforced concrete beam, size 200 mm wide and 300 mm deep overall is simply supported over a span of 3 m. It is subjected to two point loads P of equal magnitudes placed at middle third points. The two loads are gradually increased simultaneously. Beam is reinforced with 2 HYSD bars of 16 mm diameter placed at an effective cover of 40 mm on bottom face and nominal shear reinforcement. The characteristic compressive strength and the bending tensile strength of the concrete are 20.0 N/mm2 and 2.2 N/mm2 respectively. The theoretical failure load of the beam for attainment of limit state of collapse in flexure is

A reinforced concrete beam, size 200 mm wide and 300 mm deep overall is simply supported over a span of 3 m. It is subjected to two point loads P of equal magnitudes placed at middle third points. The two loads are gradually increased simultaneously. Beam is reinforced with 2 HYSD bars of 16 mm diameter placed at an effective cover of 40 mm on bottom face and nominal shear reinforcement. The characteristic compressive strength and the bending tensile strength of the concrete are 20.0 N/mm2 and 2.2 N/mm2 respectively. The theoretical failure load of the beam for attainment of limit state of collapse in flexure is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular cantilever beam has a width of 250mm and an effective depth of 480mm. It is reinforced with 7-25mm bars. The beam is carrying a uniformly distributed dead load of 15kN/m. The compressive strength of the concrete is 21MPa and the yield strength of the steel is 415MPa. The depth of the concrete stress block is?
S Maximum strain in extreme fibre of concrete and in tension steel of Fe 415 grade (E = 2 x 105 N/mm²) in a balance section in limit state of flexure are respectively (a) 0.0035 and 0.0031 (b) 0.0035 and 0.0038 (c) 0.002 and 0.0042 (d) 0.002 and 0.0038
A prestressec concrete beam 300 mm wide and 600 mm deep is prestressed using 5 high tension bors f 12 mm o provide at 220 mm from the soffit of the beam. The effective stress in the steel is 800 N/ m Find the bending that niust be applied to the section to just auoid tension at the soffit of the beam.
The end block of a post-tensioned beam is 100 mm x 150 mm. A prestressing cable consisting of 7 wires of 6 mm dia strand and stressed to 800 MPa has to be anchored at the center of the block. The anchorage plate is 75 mm x 75 mm. If the concrete mix is M45 and the permissible bending stress in M. S. steel plate is 165 MPa, determine the thickness of the anchorage plate.
A cast iron 3m long is completely filled with concrete and used as a vertical strut. If the externaldiameter of the tube is 450mm and the wall is 35mm thick, determine the maximum compressiveload the composite strut can support if the stress in the concrete is not 2N/mm2? By how muchshould the strut shorten under this load? For cast iron EA= 100GN/m2 and for the concrete EB=10GN/m2?
Pre-stressed.
Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f'c = 21 MPa and steel yield strength fy = 420 MPa a.) if the tensile strain is es = fy/Es upon crushing of concrete at a strain of 0.003 b.) if the tensioe strain is set as 0.009 upon crushing of concrete at strain of 0.003 c.) minimum as required by NSCP 2015
A rectangular beam has a width of 280 mm and an effective depth of 500 mm. It is reinforced with 4-36 mm diameter bars at the tension side of the beam placed 75 mm above the bottom of the beam. f = 25 MPa, fy = 414 MPa, E, = 200,000 MPa. Which of the following is the nominal moment capacity of the beam.
A rectangular beam with width of 233 mm and overall height of 431 mm is prestressed by using a bonded (stress relieved) tendons with a specified tensile strength of prestressing tendons fpu %3D 1380 MPa. Strength of concrete is 33.1 MPa. The area of presstressed reinforcement in tension zone is 1,024 mm2 and its centroid is located 40 mm above the bottom end of the beam. The specific yield strength of prestressing tendons fpy = 1220 MPa. Compute for the ultimate moment capacity of the beam.
What is the threshold torsion (kN-m) of a rectangular beam with a width of 446 mm and an over-all depth of 536 mm? The distance of the tension reinforcements from the bottom fiber of the beam is 75 mm. The specified compressive strength of concrete is 22.00 MPa. The yield strength of tension reinforcements and stirrups are 404 MPa and 323 MPa respectively.