A pumped water transmission line is shown in figure below. For all pipes diameter is 400mm f=0.02 Length of pipes AB, BC and BD are 1000m, 2000m and 2000m, respectively. Compute the flow rates in pipes AB, BC and BD. 1) the pump is not in operation and 2) the pump is in operation. Q (It/s) Hр (m) 100 200 45 300 400 500 50 48 41 36 30 210m 205m 200m 190m D Pump B A

A pumped water transmission line is shown in figure below. For all pipes diameter is 400mm f=0.02 Length of pipes AB, BC and BD are 1000m, 2000m and 2000m, respectively. Compute the flow rates in pipes AB, BC and BD. 1) the pump is not in operation and 2) the pump is in operation. Q (It/s) Hр (m) 100 200 45 300 400 500 50 48 41 36 30 210m 205m 200m 190m D Pump B A

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Note: Use three decimal places and no need to input the unit. A 36-in-diameter pipeline carries oil (SG = 0.89) at 1 million barrels per day (bbl/day) (1 bbl = 42 U.S. gal). The friction head loss is 13 ft/1000 ft of pipe. It is planned to place pumping stations every 10 mi along the pipe. Estimate the horsepower which must be delivered to the oil by each pump. (in hp)
Reservoirs A, B, and C are connected by pipelines 1, 2, and 3 respectively which meets at the junction D. Reservoir A is at elevation 80 m, reservoir B is at elevation 50 m, and reservoir C is at elevation 10 m. Diameter Length Friction Factor 400 mm 500 mm Pipe 1800 m 2000 m 1 0.02 2 0.025 3 800 mm 4000 m 0.03 a. Compute the discharge flowing out of reservoir A. b. Determine the discharge flowing in or out at reservoir B. c. Find the discharge flowing towards reservoir C.
In the pipe systems (a), (b), and (c) in the Figure, find the flow and velocity in each pipe and the pressure at points A. Assume all nodes are at identical elevations. m/min 20 m/min 20 m /min P- 1000 kP Sm/min 1500 m 1000 m 455 mm 405 mm 1000 m 405 mm 800 m 255 mm 300 m305 mm 300 m 205 men 1100 m 305 mm 1000 m 305 mm A500 m 205 mm 10 m/min 5m/min 10m3/min 5 m/min 15 m /min 5m/min Elev 300 m 405 mm 2000 m 150 2000 m Elev 250 m 5m/min 10 im/min 6 m/min 205 mm 205 mm 2000 m A 2000 m le) 000
answer is given just give the solution and right answer.
Determine the flow (m³/s) in each pipe in the figure shown and the elevation of reservoir C if the inflow to reservoir A is 515 L/s.
solve
2. The total flow from A to E is 300 L/s. Compute the flow for pipes 2, 3, 4, and 5 3 5 D 6 Pipe 1 2 3 4 5 6 f 0.02 0.02 0.02 0.02 0.02 0.02 Diameter Length (mm) in (m) 450 400 250 360 200 600 300 1400 250 450 300 700
Q4: The pump shown in figure (2) adds 25 kW to the water and causes a flow rate of 0.04 m³/s. Determine the flow rate expected if the pump is removed from the system. Assume f= 0.016 for both case and neglect minor losses. 40-mm-diameter nozzle (2) 60-mm-diameter, 30-m-long pipe; f = 0.016 Pump T h (1) Fig. (2)
2.2 m/min The figure represents a simplified pipe 305 mm Infiow 1000 m 25 m /min network. Flows for the area have been disaggregated to the nodes, and a major fire flow has been added at node G. 25+ m/min The water enters the system at node A. 250 mm a.5 m/min 1100 m 8 200 mm 500 m Pipe diameters and lengths are shown on the 2.0 figure. 200 mm E 500 m 1.5 m /min Find the flow rate of water in each pipe using the Hazen-Williams equation with Crw F = 100. Carry out calculations until the 305 mm 1100 m G corrections are less then 0.2 m/min. 2.3m/min 14 m/min 305 mm 305 mm 1250 m w 0001 405 mm 1250 m 355 mm 355 w 009 w 00 ww 002 C w 00
q7