A plugged dishwasher sink with the dimensions of 350 mm × 400 mm × 150 mm is being filled with water from a faucet with an inner diameter of 25 mm. If it takes 220 seconds to fill the sink to its rim, estimate the mass flow of water coming out of the faucet. Problem 9.34 Saeed Moaveni

Q: Q/A uniform flow with a velocity of 4 m/s is flowing over a source placed at the origin. The…

A: Given: Uniform velocity (U)=4m/sStagnation points= (-0.35,0)

Q: the siphon shown in the  figure, calculate (a) The mass flow rate of oil from the tank and (b) The…

A: To determine the mass flow rate and pressure at point D.

Q: Water is flowing steadily through a closed pipe system of constant diameter. Station 2 is 1 m higher…

A: Given data: The height of station 2 is, z2 = 1 m. The velocity at station 1 is, v1 = 3 m/s. The…

Q: A frictionless convergent-divergent channel is used to accelerate the airflow emanating from the…

A:

Q: The ethanol solution is pumped into a vessel 25 m above the reference point through a 25 mm diameter…

A: As per Bartleby Policy, in case of multiple subparts, only the first three subparts can be solved,…

Q: Fluid A is three times denser than Fluid B through the same horizontal pipes. Which will flow…

A: The fluid is the substance that offers resistance to flow. Basic fluid properties are density…

Q: respectively. The outlet end is 2m above the inlet end. Calculate the magnitude and direction of the…

A:

Q: The choked nozzle that converges and diverges. Find the nozzle areas ratio that divides by the…

A:

Q: Water issues from the-14 nozzle of a horizontal hose- pipe. The hose has an internal diameter of 70…

A: Find the flow rate through the pipe.

Q: Q2/A Kaplan turbine develops 1500 kw under ahead of 6 m. the turbine is set 2.5 m race while the…

A: Given data as per questionPower develop by Kalpan turbine, P=1500 kWHead, H=6 mDraft tube has…

Q: plain the velocity and pressure behavior of the fluid through venturi. Also explain how to measure…

A: given: Explain the velocity and pressure behavior of the fluid through venturi. Also explain how to…

Q: 5 Water flows through a horizontal pipe that has and 2 cm at the exit. The pressure drop across t…

A: Given data as per question Diameter of pipe at entrance, d1=4 cm=0.04 mDiameter of pipe at exit,…

Q: A venturi meter is introduced in a 300 mm diameter horizontal pipeline carrying a liquid under a…

A:

Q: flowing through a pipe of diameter 480 mm at the rate of 375 litres per sec. Find the Reynold's…

A:

Q: À venturimeter is inserted a 150 mm dia If the differential head indicated by the rate of flow is 80…

A:

Q: Determine the velocity of efflux from the nozzle in the wall of the reservoir of (a) * .Figure, (b)…

A:

Q: In a syringe the plunger has a face area of 500 mm^2. If the liquid is to be injected steadily of a…

A: Given Cross-sectional area = 500 mm2 = Volumetric flow rate = 300 cm3/s Leakage rate = 0.1 of…

Q: ● Compute the time needed for the cylinder position to retract from the maximum position 1m to…

A:

Q: A very popular toy on the market several years ago was the water rocket. Water (at 10°C) was loaded…

A: Given Pressure inside the rocket , Pi = 100 KPa exit area is on tenth of the inside area .

Q: A hose pipe of 75 mm bore and length 450 m is supplied with water at 1.4 MPa. A nozzle at the outlet…

A:

Q: Air enters the room through a 200 mm diameter pipe and exits the fan into the ambient air through…

A:

Q: As seen in the figure above, the water is directed downward in the installation with a 25 ° angle…

A: (a) Write the formula for discharge to calculate the velocity at section 1 in the given figure.…

Q: Problem 3: Control Volumes When a water jet strikes a stationary inclined plate, it breaks into two…

A: if you have any doubts please comment

Q: A 15 m building use cast iron pipes in their piping system. The water tank located on the top of the…

A:

Q: 3. Problem: What head H must be created at the beginning of the oil line in order to ensure the…

A:

Q: Don't use chatgpt will upvote

A:

Q: The water (density =1000 kg/m3) leaves the nozzle (area of the nozzle%3D0.01 m ). Assuming steady,…

A:

Q: onsider the hydropower schematic shown below with a lake of 70m elevation above a turbine house.…

A:

Q: Water at 15°C flows through a small pipe 5 mm in diameter. The average velocity is measured to be…

A:

Q: There is a pipe burst through developed orifice of 1 centimeter in diameter with leakage rate of 0.1…

A: Given data  Diameter of orifice (D) = 1 cm  Leak rate (Q) = 0.1 m3/s Pressure at burst portion (P) =…

Q: Calculate the inside diameter of the pipes at the inlet and outlet a hydraulic pump whose volume…

A: Given : flow rate Q = 40 Lit/min = 40 x 10-3 m³ / 60 sec = 6.67 x 10-4 m³/s entry velocity V₁ =…

Q: Consider the pipe shown in the figure below. The nozzle's center line is 0.3 m above the flange…

A:

Q: In the friction- free siphon shown below, a) what are the pressures of the water in the tube at ( B)…

A:

Q: Oil, with a vapor pressure of 20 kPa, is delivered through a pipeline by equally spaced pumps, each…

A:

Q: A reducing bend with an inlet diameter of 200 mm and exit diameter of 150 mm bends 40 degrees…

A:

Q: Centrifugal pump is a kinetic device and uses the centrifugal force to push out the fluid. So the…

A: Centrifugal pumps works by  transferring the low viscosity fluids in high flow rates, within low…

Q: A plugged dishwasher sink with the dimensions of 15 in. ✕ 19 in. ✕ 9 in. is being filled with water…

A: Dimension of sink = 15 in × 19 in × 9 in  t1 = 210 sec t2 = 230 sec Find the flow rate of leak .

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.