A load of P = 119 kN is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 106 GPa] rods, and a solid steel [E = 201 GPa] rod, as shown. The bronze rods (1) each have a diameter of 18 mm and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 25 mm. All bars are unstressed before the load P is applied; however, there is a 2.9-mm clearance in the bolted connection at B. Assume L₁= 2.5 m and L₂ = 1.5 m. Determine: (a) the normal stresses in the bronze and steel rods (01, 0₂). (b) the downward deflection v of rigid bar ABC. (1) Answers: (a) σ₁ = (b) v = i L2 F (2) B (1) L₁ MPa, 0₂ = mm. M MPa.

A load of P = 119 kN is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 106 GPa] rods, and a solid steel [E = 201 GPa] rod, as shown. The bronze rods (1) each have a diameter of 18 mm and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 25 mm. All bars are unstressed before the load P is applied; however, there is a 2.9-mm clearance in the bolted connection at B. Assume L₁= 2.5 m and L₂ = 1.5 m. Determine: (a) the normal stresses in the bronze and steel rods (01, 0₂). (b) the downward deflection v of rigid bar ABC. (1) Answers: (a) σ₁ = (b) v = i L2 F (2) B (1) L₁ MPa, 0₂ = mm. M MPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The pin-connected assembly consists of aluminum rods (1) and (2) and steel rod (3). The aluminum rods each have a diameter of 13 mm and an elastic modulus of E = 70 GPa. The steel rod has a diameter of 20 mm and an elastic modulus of E = 190 GPa. Assume a = 4.8 m, b = 1.9 m, and c = 1.2 m. What is the magnitude of load P that is necessary to displace point A 14 mm to the left? a b (1) P Answer: P = i (3) B KN O
Solid
solve the problem
The compound shaft consists of a solid aluminum segment (1) and a hollow brass segment (2) that are connected at flange B and securely attached to rigid supports at A and C. Aluminum segment (1) has a diameter of 0.55 in., a length of L1 = 55 in., a shear modulus of 3800 ksi, and an allowable shear stress of 5.8 ksi. Brass segment (2) has an outside diameter of 0.35 in., a wall thickness of 0.07 in., a length of L2 = 38 in., a shear modulus of 6400 ksi, and an allowable shear stress of 8.3 ksi. Determine:(a) the allowable torque TB that can be applied to the compound shaft at flange B.(b) the magnitudes of the internal torques in segments (1) and (2).(c) the rotation angle of flange B (relative to support A) that is produced by the allowable torque TB.
Rigid bar ABC is supported by bronze rod (1) and aluminum rod (2), as shown. A concentrated load P is applied to the free end of aluminum rod (3). Bronze rod (1) has an elastic modulus of E1 = 15,000 ksi and a diameter of d1 = 0.45 in. Aluminum rod (2) has an elastic modulus of E2 = 10,000 ksi and a diameter of d2 = 0.75in. Aluminum rod (3) has a diameter of d3 = 0.95in. The yield strength of the bronze is 48 ksi and the yield strength of the aluminum is 40 ksi. Assume a = 2.5 ft, b = 1.5 ft, L1 = 6 ft, L2 = 8 ft, and L3 = 3 ft.FIND: (a) Calculate the cross-sectional areas of the three rods.(b) For a factor of safety of 1.9, calculate the allowable stresses in the bronze and the aluminum rods. (c) On a piece of paper, sketch a free body diagram (FBD) cut through rod (3) and also a FBD of the rigid bar. Using these, find a relationship between the force in rod 1 (F1) and the applied load, P, a relationship between the force in rod 2 (F2) and the applied load, P, and also a relationship…
A small aluminum alloy [E = 79 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 155 mm. The cross- sectional dimensions of the tee shape are b = 16 mm, d = 24 mm, and t = 8 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 410 uɛ is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? 3P Strain gage - d D E H b Answer: P= i N
[] : Diameter=38 [] : Length=0.8
Please show your solution on a paper with FBD
Q2: The pin-coected structure shown in figure below consists of a rigid member BED and three steel rods (E- 200 GPa). Each of the rods AB and CD has a 200 mm cross-sectional area and rod EF has a 625 mm2 cross-sectional area. If a load of P- 36 KN is applied at E, determine: (a) the change in length of rod EF. (b) the stress in each rod. 300 mm P-36 kN 300 mm 400 mm * 500 mm
The rigid bar of negligible weight is supported as shown. The assembly is initially stress-free. Find the stress in each rod if the temperature rises after a load W = 120 kN is applied. Steel rod Bronze rod A (mm²) 350 1500 a (/°C) 11.7 x 10-6 18.9 x 10-6 E (GPa) 200 83 O Steel 1.5 m 1.0 m- 2.5 m 9. Determine the stress at the steel rod in MPa when there is a temperature rise of AT = 36 °C. W Bronze 3 m 1.5 m-
SHOW COMPLETE SOLUTION AND ILLUSTRATION
Determine the normal stress (in Mpa) in member AC of the truss shown if it is made up of a 22-mm-square bar of alloy and the load P is 20.15 kN. Express your answer in two decimal places.