A level was put between two points, A and B, the readings were(2.597m), (1.594m) respectively, then it was put near point A by 3m and the readings were (2.596m), (1.590m) respectively, what will be the corrected reading at Band if the elevation of A ,was(30.500m), obtain that of B.

A level was put between two points, A and B, the readings were(2.597m), (1.594m) respectively, then it was put near point A by 3m and the readings were (2.596m), (1.590m) respectively, what will be the corrected reading at Band if the elevation of A ,was(30.500m), obtain that of B.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Complete the following level notes. Show your detailed solution and checking. Differential Leveling…

A: We know that,Height of instrumentHI=Elevation of Bench mark+Back sightBSandEleavation of a…

Q: differential leveling circuit began on BM Hydrant (orthometric height 5869.31 ft) and losed on BM…

A: StationB.SH.IF.SElevationAdjusted Elevation(R.L)B.M…

Q: Q1): A field book is reproduced below in which some readings marked as (x), are missing. The true…

A: We have to determine the complete all missing data and perform all asthmatic checks and compute…

Q: A line of levels 15 km is run on a soft ground to check the elevation of BM-2 which has been found…

Q: (8) A tacheometer and the following staff vertically held was set up at a station C readings were…

Q: The following consecutive staff readings were taken with level and 5m staff at 70 m interval. The…

A: Given, Elevation at first point and last point= 80m and 84.96m

Q: calculate the R.L.

A: Given: benchmark=432.384 To find: Fill level book and calculate RL of points

Q: (c) A Dumpy Level was place at the mid point C of A and B which were 200 ft apart. The staff…

Q: Based on the level loop problem. What is the calculated elevation of BM_10 ?

A: Given: The reduced level of BM10 is 701.32'. To Determine: The calculated elevation of BM10.

Q: HI HELP PLEASE WITH THE OBJECTIVE, INTRODUCTION AND CONLUSION(ATTACHED PHOTO ARE THE DATA AND…

A: To determine the elevation difference between BM-a and BM-b.

Q: 1. DIFFERENTIAL LEVELING STATION BACK SIGHT HEIGHT OF INSTR. FORESIGHT ELEVATION BM 10 4.64 209.65 m…

Q: Which one of the following is a significant error in leveling? а. Таре O b. Average level C. Reduced…

A: There are many causes of errors in levelling, among the above options given the significant error is…

Q: A differential leveling circuit began on BM Hydrant (orthometric height 5869.31 ftft) and closed on…

A: BM Hydrant = 5869.31 ft BM Rock = 5830.03 ft

Q: 10. Complete the following table using the knowledge obtained in class about differential leveling…

A: Given Data Total 5 stations has been given and we are asked to calculate the Elevations, adjusted…

Q: Determine elevation the top of a tower from the following observation.. Inst. St. Target Reading on…

A: Answer The elevation of the top of a tower is 107.617 The solution is shown below

Q: II. Complete the leveling note and perform the arithmetic check based on the picture Result Reviewer…

A: ELEV OF BM20 = 131.239

Q: 6. The azimuth from north of traverse line AB is 220° 02'. If the succeeding line BC has a bearing…

Q: A line of levels has been run from a bench mark of elevation 24.56 m and ends at another mark of…

A: given- elevation of bench mark=24.56 mother elevation=24.60 msum of back sight BS=18.36 msum of…

Q: Direct Differential Leveling Data: Staff Reading at Level at A K 1.115 m 0.989 m 15 2.113 m 1.867m…

A: Dear student as per bartleby guidelines we are supposed answer only first 3 sub parts. Kindly repost…

Q: 59. The back staff reading on a B.M. of R.L. 500.000 m is 2.685 m. If foresight reading on a point…

A: given- Reduced level of BM=500 mBack staff reading BS=2.685 mforesight readig FS=1.345 m

Q: STA BS HI FS ELEV BM1 2.883 130.016 127.133 ТР1 2.743 129.710 3.049 126.967 ТР2 2.855 129.876 2.690…

A: Leveling is the linear measurement process in which we establish the leveling instrument and…

Q: Show complete solution and answer in the nearest 4 decimal places. An engineer's transit is setup at…

Q: In carrying out the permanent adjustments of a level by, the following observations were made:…

A: Data given Instrument set up 1 Instrument set up 2

Q: Problem 1. From the given data of a three wire leveling as shown in the tabulation: Point Backsight…

A: The given table is shown below:

Q: level 200, the leve another point B. Th point B was found order to check the

Q: omplete the table of information and calculate the difference in elevation of ation 0+ 020 and…

A: HERE BS FS AND IS ARE GIVEN .RL IS ALSO GIVEN THATS IS 200

Q: A total station was setup on top of point A. The Target Point Occupied Point OUSCI · rations…

A: given data,total station is setup at Asloping distance and vertical angles are given elevation of…

Q: The following data was obtained with the level. What is the HI of the instrument Sta. BM ΤΡΙ TP2…

A: For first part of the question the HI can be calculated where BS is taken that is for first two rows…

Q: A differential leveling circuit began on BM Hydrant (orthometric height 5869.31 ft) and closed on BM…

A: BM Hydrant BM Rock Readings (in feet) given in the order taken are, 2.68 (+S) on BM Hydrant, 5.59…

Q: Complete the following level notes. Show your detailed solution and checking. Differential…

Q: Two pegs A and B were fixed on opposite banks of a 40 m wide river. The level was set up at A and…

Q: Q.I A line of level is run from B.M.1 (elevation-106.40m) to B.M. 2(clevation-110.50m). The field…

A: The field observations were recorded as given in question, Given B.M.1 (elevation=106.40m) B.M.2…

Q: A differential leveling circuit began on BM Hydrant (orthometric height 5869.31 ft) and closed on BM…

A: BM Hydrant =5869.31 ftBM Rock (orthometric height 5830.03 ft). Readings 2.28 (+S) on BM Hydrant,…

Q: The following consecutive staff readings were taken with level and 5m staff at 70 m interval. The…

A: AS height of instrument method

Q: then RL (in m) of R is

A: Given data. Rl of point R with respect to the bench mark at P.Staff reading is shown in graph…

Q: What is the calculated value of BM_13 before adjustment ?

A: Given:R.L. of B.M.-10=701.32'We know that,Height of instrumentHI=R.L. of B.M. of known elevation+…

Q: i): A field book is reproduced below in which some readings marked as (x), are missing. The true…

A: Given Levelling readings BS, FS, and IS To compute the RL by Rise and Fall method Omitted…

Q: Ql: -In leveling, the following readings were taken starting from B.M. of (29.386m) elevation, then…

Q: the elévation of A=40.444m. Q2- The following readings were recorded in leveling (2.811, 1.969,…

A: Given Readings at 11 station points. B.M1 = 30.444 m To Determine Elevation of all the points and…

Q: B. Double-Rodded Leveling 3. Complete differential level notes for the information shown and perform…

A: Height of instrument = B.M + B.S Reduced level = H.I - F.S/I.S

Q: В.М I.S F.S H.I ELeve.(m) Rem 1.34 1.33 0.95 1.139 1.319 1.48 1.33 1.37

Q: Prepare a set of level notes for the data listed. Perform a check and adjust the mis- closure.…

A: Given data,

Question

A level was put between two points , A and B, the readings were(2.597m),
(1.594m) respectively, then it was put near point A by 3m and the readings were
(2.596m), (1.590m) respectively, what will be the corrected reading at B and if
the elevation of A ,was(30.500m), obtain that of B.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Construction Surveying
Question 49 In leveling across a river, reciprocal level readings were taken between two points A and B. From a set up near A: on A, 0.994 and 0.992 m; on B 2,076, 2.077, 2.078 and 2.077 m. At the set up near B: on H, 2.550 and 2.548m; on A, 1.462, 1.463, 1.464 and 1.463. From the observed data it can be determine that A. B is 1.085 m below A B. B is 1.085 m above A C. A is above B by 1.088 m D. A is below B by 1.084 m E. A and B are of the same elevation
Ex-2-: In a levelling process the readings were recorded as following: (1.349, 1.723, 1.522, 1.634, 1.542, 1.773, 1.829 m). If the Level instrument was relocated after the fourth reading and the level of the fourth point was (30 m). Calculate the elevations of the other points and do check your calculations.
Reciprocal leveling gives the following readings in meters from a set up near A: on A, 1.110; on B, 0.887, 0.995, and 0.884. At the setup near B: on B, 1.549; on A, 1.673, 1.670, and 1.666. The elevation of A is 1045.343 m. Determine the misclosure of B. Express your answer to three decimal places and include appropriate units. Misclosure = Submit Part B elevB = μÁ Value Request Answer CHA Value Units Determine the elevation of B. Express your answer to three decimal places and include appropriate units. Units ? ?
Q2/ Complete the settlement table below and verify the correctness of the calculations. Then check the correctness of the work, bearing in mind that the length of the leveling line is 2,250 meters, bearing in mind that the required level of leveling is the third. Find the closing error and adjust the levels if necessary, suppose that the error equal for all points. Elevation Station B.M1 TP1 TP2 TP3 TP4 TP5 TP6 BM1 B.S 1.23 0.955 1.332 1.652 2.558 2.465 2.882 H.I F.S 1.735 2,642 3.000 2.524 2.221 0.755 0.218 50,000
In carrying out the permanent adjustments of a level by, the following observations were made: Instrument at peg (C) midway between points A and B, 100m apart. Readings at points A and B are 2.500m and 3.500m, respectively. Instrument at peg (D) in line of AB such that AD-120m and BD-20m, Readings at points A and B are 1.500m and 2.600m, respectively. Check whether the instrument needs permanent adjustment or not and whether the line of sight is inclined upward or downward. What should be the correct reading at (A and B) if the instrument is to be adjusted?
From the given data of a differential leveling as shown in the tabulation: STA. B.S. H.I. F.S. ELEV. A 5.87 329.25 7.03 6.29 3.48 6.25 D 7.25 7.08 E 10.19 5.57 9.29 4.45 G 4.94 a.) Find the difference in elevation of station F and station E. b.) Find the difference in elevation of station G and station B. c.) Find the elevation of station D.
Q3: Find the elevation of all point if the elevation of Last point is 30 m and check the results. (25 %) Station B.S F.S elevation В.М 1.245 T.P, 3.254 2.523 T.P2 2.522 1.421 T.P3 1.242 0.263 3.486 30
The back staff reading on a B.M. of R.L. 1000.000 m is 1.663 m. If foresight reading on a point is 0.974 m, the reduced level of the point is: Select one: a. 997.363 m b. 1000.689 m c. 1000 m d. 1002.637 m
Two points of A and B on opposite bank of a river, the level was setup near A and staff readings at A and B were (1.72) and (1.315 m) respectively. The level was changed to near B and respective staff readings on A and B were 1.51 m and (R) m, elevations of A and B are 299.735m and 300.415 m respectively, find value of (R).
Complete the table below. STATION BM1 A B C D E F BM2 BS 1.470 1.967 2.792 2.225 2.209 1.072 HI 368.382 369.414 370.245 Lowest rod reading Station with the Highest BS Lowest Elevation 370.780 370.278 371.138 Highest elev of the line of sight Station with the highest elevation (excluding BM1 & BM2) FS 1.200 1.136 1.082 3.400 0.212 1.204 ELEV 367.182 368.278 369.163 368.555 368.069 369.934
3 - please provide correct answers