A half-coned shaped resistor shown in Figure is composed of two different ohmic materials with different resistivities. materials are shaped into individual cones of radii R, and R, .The total length of the half cone is L. Which of the statements about the total resistance of the composed material for currentthrough the length of the half cone islare true? I) It is constant for a given temperature. I) It is not constant because the cross sectional are which the current passes is not constant. I) It is not constant because the composed material does not have a uniform resistivity. MIt is constant as long as the current passing is constant. O A) Il and II O B) I and IV

A half-coned shaped resistor shown in Figure is composed of two different ohmic materials with different resistivities. materials are shaped into individual cones of radii R, and R, .The total length of the half cone is L. Which of the statements about the total resistance of the composed material for currentthrough the length of the half cone islare true? I) It is constant for a given temperature. I) It is not constant because the cross sectional are which the current passes is not constant. I) It is not constant because the composed material does not have a uniform resistivity. MIt is constant as long as the current passing is constant. O A) Il and II O B) I and IV

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

QUESTION 4 a) Remote control is connected to a stereo by 20 m distance by using copper wire. This copper wire has a resistivity of 1.7x10* Qm What should be the diameter at the end of the wire if the resistance of wire must be less than 0.10 0?
A particular wire has a resistivity of 4.5 x 108 N · m and a cross-sectional area of 5.3 x 10-6 m². A length of this wire is to be used as a resistor that will receive 49 W of power when connected across a 20-V battery. What length of wire is required? You may have made an error in converting or using units. km Need Help? Read It Master It
3
Two steel conductors are bent into rectangular prisms with square bases of lengths a and, where /-2s. If the thin prism has a length of L-10s and the thick prism has a length of Ladda; compare the resistances of the two conductors: Select one: II a. The thicker conductor has smaller resistance b. The thinner conductor has smaller resistance c. They have equal resistances d. We cannot answer the question with the information provided
the 0.115 mm diameter tungsten filament in a light bulb is to have a resistance of 0.132 2 at 20.0°C, how long should it be? The resistivity of tungsten at 20.0°C is 5.60 x 108 n. m. Additional Materials O Reading
The current i, in the circuit in Figure below 2 A. a) Find iz. b) Find the power dissipated in each resistor. 60N 50 25 1 180V 70N 350
Please insert the photo of the plot please
Not hand writing solution provide text solution
Physics Please solve the following question and include a section showing the formulas that would be used also please include units in each part of the answer. Thank you for your help! A wire has an electric field of 6.2 V/m and carries a current density of 2.4 x 10^8 A/m2. Show that its resistivity is 2.6 x 10^-8 Ω*m without using this formula, ?=?/?!
R1 R2 RA 1. In the figure above, let R1 = 10N, R2 = R3 = 5 N, and R4 = 8N respectively with a battery whose emf is E = 9 V. Find the current and potential drop across each resistor. Assume that current is going in clockwise direction.
Two wires have the same length and the same resistance but are made up of different materials. The resistivities of these materials are 1.38 Qm and 3.07 Qm. Obtain the ratio of the smaller cross-sectional area to the greater cross-sectional area. Number i Units
a) Remote control is connected to a stereo by 20 m distance by using copper wire. This copper wire has a resistivity of 1.7x10* Qm. What should be the diameter at the end of the wire if the resistance of wire must be less than 0.10 Q?