A fuel oil of 21 deg API (density = 934 kg/m³) is to be heated in aheater and has the following properties:Quantity of oil to be heated3000L/hrTemp. of oil entering tubes220Temp. of oil leaving tubes970Heating fluid, steam enters at 103C and leaves as condensate at83C. Assume specific heat of oil to be 2.093 kJ/kg-K. Take the over-all coefficient of heat transfer is as 140 W/m²-C.What is the required heat transfer area (m^2)?A =

Answered: Image /qna-images/answer/51eed211-615d-44b8-9b18-affe9f2b08b5.jpg

A fuel oil of 21 deg API (density = 934 kg/m³) is to be heated in a heater and has the following properties: Quantity of oil to be heated 3000L/hr Temp. of oil entering tubes 220 Temp. of oil leaving tubes 97C Heating fluid, steam enters at 103C and leaves as condensate at 83C. Assume specific heat of oil to be 2.093 kJ/kg-K. Take the over- all coefficient of heat transfer is as 140 W/m²-C. What is the required heat transfer area (m^2)?

A fuel oil of 21 deg API (density = 934 kg/m³) is to be heated in a heater and has the following properties: Quantity of oil to be heated 3000L/hr Temp. of oil entering tubes 220 Temp. of oil leaving tubes 97C Heating fluid, steam enters at 103C and leaves as condensate at 83C. Assume specific heat of oil to be 2.093 kJ/kg-K. Take the over- all coefficient of heat transfer is as 140 W/m²-C. What is the required heat transfer area (m^2)?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Note: No rounding off in the solution
In a cyclic comprising of air compressor and expansion, workdone by a prism during the compression stroke is 9.2KJ and the heat rejected to the surrounding is 50KJ. During the expansion stroke workdone by air on the prism is 8.4KJ. a) Determine the quality of heat transferred to or from the system. Tullow oil has discovered a large volume of crude deposit at Cape-3-Point along the western coast of Ghana after years of intensive exploration. In the Company’s bid to start exploration, Green Ghana an environmental protection NGO took Tullow to court to prevent the Company from embarking on the said project citing numerous environmental concerns. b) As an energy and sustainability expert, what do you think are the side effects of the project and their remedies? A cooling water pump is operating at a speed of 1800rpm. Its flow rate is 1800L/minutes at a head of 14.4m and the power of the pump is 45kw. c) Determine the power required if the pump speed is increased…
A water tube boiler produces 250,000 pounds of steam per hour at 1200 psia and1000°F from feed water entering the boiler at 1500 psia and 360°F. Fuel oil havinga higher heating value of 18,200 Btu/lb is supplied to the burners at the rate of20,700 lb/hr. Furnace volume is 1500 cubic feet. Calculate the equivalentevaporation, lb/hrA. 300,117 B. 300,317 C. 300,517 D. 300,717
A freon 12 waste water system operating at 5 °C suction temperature and a 40°C condensing temperature has an evaporator load 17.6 KW. If the condenser is selected for a 70°C water temperature rises, how many gpm must be circulated through the condenser? The following enthalpies have been found; condenser entrance =377 kJ/kg; exitA=238.5 kJ/kg; evaporator entrance =238.5 kJ/kg; exit = 253.6 kJ/kg.
if A 22 C Water enters a heat exchanger with a velocity 0.8 m/s and tube diameter is 10 mm, it leaves at 34 C what is the heat transferred to water. in kW 3.157 O 31.569 O 3.94 O
helpp
ROOM (2) 700kPa x-0 CONDENSER k (1) 40°C 700OkPa EXPANSION VALVE (3) 100kPa EVAPORATOR (4) 100kPa x=1 OUTSIDE Consider a heat pump cycle operating with R134-a fluid at 0.01kg/s mass flow rate. Conditions are given in the figure. a) What are the values of heat supply rate to the room and heat absorption rate from the outside? b) What is COP of this heat pump? c) Assume we immediately put a watermelon of 8kg to the room at 2°C. Assuming a specific heat of 4200J/kg for the watermelon, how long will it take for the watermelon to reach room temperature of 20°C if we assume that heat pump only heats watermelon? CA122.minutes O D112 menute COMP.
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 16.3846 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case:
S2
The condensing pressure for a Rankine engine is 0.001325 MPavac. Calculate the following for steam flow rate = 1 kg/sec of steam when the steam at the beginning of expansion is at 119.6 deg SH and 4.0 Mpaa. Draw the TS and equipment diagrams for the ideal and actual case and find for the following for the ideal case:
A 95kg/hr hot fluid is used to heat a cold fluid from 10oC to 70oC using a double pipe heat exchanger (DPHE). The hot fluid enters at 205°C and leaves the DPHE at 108°C. The Cp of hot fluid is 1.10 kcal/kg°C and the Cp of cold fluid 0.95 kcal/kg°C. a) Calculate the LMTD if the the flow is cocurrent in oC b) Calculate the LMTD if the the flow is countercurrent in oC
The condenser of a steam power plant has a total surface area of 45m^2 and an overall heat transfer coefficient of 2100Watts/m^2-K. Saturated steam from the turbine enters this condenser at 30C and leaves as saturated liquid at the same temperature. Cooling water enters the condenser at 14C and leaves at 22C. A. Draw the figure, sketch the t-L diagram, then, compute the LMTD of the cross-flow heat exchanger in Kelvin. B. How much heat is transferred by the condenser in MW? C. How much steam passes through the condenser in kg/s? D. How much cooling water is supplied to the condenser in kg/s.