a) Find the location of the shear center for a beam with the cross-section shown in Fig. 6. All dimensions are in mm. Here, ID = Last Three Digits of Student ID. Id:19.02.03.061 SC e*150 mm Fig. 6 b) The radius of a cylindrical water reservoir is 1500 mm and its wall thickness is 12 mm. If the height of water in the tank is (30+0.1*ID) m, (a) Determine the hoop and longitudinal stresses at the bottom of the cylindrical wall caused by an internal pressure exerted by water (b) Calculate the change in radius of the tank caused by pressurization. Given, E= 180 GPa, v = 0.25 and unit weight of water is 9.81 kN/m'. Here, ID = Last Three Digits of Student ID. +8 mm (300+ID) mm

a) Find the location of the shear center for a beam with the cross-section shown in Fig. 6. All dimensions are in mm. Here, ID = Last Three Digits of Student ID. Id:19.02.03.061 SC e150 mm Fig. 6 b) The radius of a cylindrical water reservoir is 1500 mm and its wall thickness is 12 mm. If the height of water in the tank is (30+0.1ID) m, (a) Determine the hoop and longitudinal stresses at the bottom of the cylindrical wall caused by an internal pressure exerted by water (b) Calculate the change in radius of the tank caused by pressurization. Given, E= 180 GPa, v = 0.25 and unit weight of water is 9.81 kN/m'. Here, ID = Last Three Digits of Student ID. +8 mm (300+ID) mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

B P A y W Find the Vertical Position of the Centroid marked as y on the Diagram using the transform section method, transforming all your material to Material A. Your Answer should be in mm to 1 decimal place. J-22.0 mm, P=76.8 mm, W-187.2mm, Young's Modulus of Material A = 64.5 GPa, Yield Stress of Material A = 145.9 MPa, Young's Modulus of Material B = 94.4 GPa, Yield Stress of Material B = 272.9 MPa.
PROBLEM 4 - A solid shaft given below is made from two segments: AC has a diameter of 15 mm and CB has a diameter of 10 mm. Determine the support reaction at point B and clearly statie its direction if it the shaft is fixed at points A and B and is subject to a torque 7' at point D. Take the shear modulus as 50 GPa. Write your final answer in the textbox below. Hint: J0.5ne, where e is the radius. 15 10 mm D. B. T 20 Nm 1m 0.5 m 2 m Wall
4 m 450 mm [s0 mn [50 mn 18 350 mm 50 mm Figure la Figure Ib Before a diver jumps into the water, helshe stands at point C, causing a deflection of the board A-B-C in the figure. The board A-B8-C has a modulus of elasticity of E = 15 MPa with the sketched dimensions and cross-section (fig. 1b). Assume g=10 mis?. Provide all steps of your working and solutions handwriten; include diagrams and coordinate systems. a. Determine the reactions at each support A and B. Use the variable w for the weight of the diver, include a free-body diagram.
Problem 2 For the simply supported beam shown below, determine whether the beam is cracked or un-cracked under the applied loads, use f'e = 25 MPa, if the beam is cracked calculate the bending stresses in the beam using the transformed area method. 20 KN 300 mm 4 kN/m A↓ D 3025 k 3 m 3 m 500 mm - աա St
Solve the given problem. Round off answers in all computations in 4 decimal places. Determine the moment capacity of the beam shown in the figure.
Problem 5 The load has a weight of 950 lb. -1.5 ft- 1 in. max = Section a - a Q Tap image to zoom Part A Determine the maximum normal stress developed on the cross section of the supporting member at section a-a. Express your answer in kilopounds per square inch to three significant figures. Enter negative value in the case of compression and positive value in the case of tension. ANSWER: ksi
2. Determine the centroid for the following figure: 2.5 E2.5"- 1.5" 3"
A beam shown below, 200mm wide by 350mm deep, is loaded as shown in figure below. Determine the stress in a fiber 50mm from the top of the beam at point B. 50kN A 20 купи RI B 2M X 30KN/M TITT. 4m 20 km. ITTJ 2m + <
A pump is driven from an engine crank-shaft by the mechanism as shown in Figure . The pump piston shown at F is 250 mm in diameter and the crank speed is 100 r.p.m. The dimensions of various links are as follows: OA = 150 mm ; AB mm; DE = 500 mm. Determine for the position shown: 1. The velocity of the cross-head E, 2. The rubbing velocity of the pins A and B which are 50 mm diameter. 3.The acceleration of the cross-head E. 45 A 300 600 mm ; BC = 350 mm ; CD = 150 %3D 450 100 1111 All dimensions in mm.
For questions 1 to 5, consider a bent rod fixed at the wall at A and is acted upon by a 20- N force (parallel to the z-axis) and a 50-N force (parallel to the y-axis) applied at points B and C, respectively. y Z A Rx, Mx Ry, Mx, My, Mz Rx, Ry, Rz, My, Mz Rx, Ry, Rz, Mx, My, Mz -4 m- C -2 m- 50 N 20 N. x B X 5. Which of the following are the reactions at the support at A? R are force reactions and M are moment reactions.
Q3: Figure (3) shows a punching machine of plate (thickness 2 mm).Punching operation is applying many times to make thousands holes (d-4 mm) through cam (2) which attaches with the ram (1) from two sides and moves it up and lowering down by action of weight (1000N). Assume the ram (1) is circular cross section. Requirement: Select the correct answer of following: 1. The ram (1) subjected to static bending stress at section (X-X): 1800ND Flgure (3) X- B. 100 mm A: True B: False 2. The ram (1) subjected to reversed load at section (Y-Y): B. False 3. The diameter of ram (1) at section (X-X) is (44603 mm): B: False 1- A: True A: True 4. The diameter of ram (1) al section (Y-Y) is (9.694 mm): B: False A: True For ram (1) and pin (b): S,-160 MPa S,-210MPA S-100MPA 5. The torque required to rotate cam (2) is (10000 N.mm): A: True B: False 6. The plate material can be punched by this mechanism has (S,-39.788 MPa): N= 2.5 A: True 7. The diameter of pin (b) on the ram (1) is (6.307 mm): B: False…
Example #2: Determine the largest weight W that can be supported by two wires shown in Fig. P- Figure P-109 109. The stress in either wire is not to exceed 30 ksi. The cross-sectional areas of wires AB and AC are 0.4 in? and 30° 50° 0.5 in?, respectively. W