(a) Figure Q2(a) shows an operation of a stepper motor that has four teeth of stator and two teeth of rotor. (1) Determine the type of stepper motor drive that has been used. (ii) llustrate the pulse sequence supply to the stator to make the rotor rotate from step 1 to step 4 as shown in Figure Q2(a) using bipolar and unipolar wave.

(a) Figure Q2(a) shows an operation of a stepper motor that has four teeth of stator and two teeth of rotor. (1) Determine the type of stepper motor drive that has been used. (ii) llustrate the pulse sequence supply to the stator to make the rotor rotate from step 1 to step 4 as shown in Figure Q2(a) using bipolar and unipolar wave.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q1 Describe the Characteristics, characteristics, efficiency calculations, their applications Of DC Motors in detail
Answer the question?
A hybrid stepper motor has four stator poles and two 5-pole permanent magnet armatures, as shown in Figure Q3. A1 armature 1 armalure 2 A2 Figure Q3 Describe how the motor can be excited by a two-phase source to rotate in the counterclockwise direction.
(c) What are the principle characteristics of DC series motor and DC compound motor, and what are its uses?
The armature resistance of a shunt motor fed from a 220 Volt DC source is 5 ohms and the resistance of the excitation winding is R ohm and it rotates stably. Then, a resistance of R ohm is added to the excitation circuit (a resistor with the same value as the winding resistance) to control the speed. How many RPM is the motor in the last state in steady state.Mechanical losses will be neglected, motor magnetically linear, no saturation, temperature change will be neglected.Armature current = Ia = 3 ALoad torque=Tload= 8 Nma) 143 rpmb) 734 rpmc) 1361 rpm d) 77 rpm e) 1333 rpm
The relation between armature torque and armature current of a DC motor is Parabolic Linear Inverse Exponential
The rotor of the 4-pole three-phase squirrel cage induction motor has been replaced with the rotor of the three-phase 4-pole rotor wound induction motor. When the motor is fed with normal supply, the machine will a) Does not work b) Runs at a very slow pace c) Runs at slightly lower speed than normal speed d) Runs at a slightly higher speed than normal speed e) none
Please all subparts
The supply voltage to a DC motor is 160V. If the back emf Ez=155V and the armature resistance A6 is 0.250, the armature current is a) 5A b) 10A c) 15A d) 20A 1800 ro/min The frequency
Compare the properties of induction motor and synchronous motor.
The armature resistance of a shunt motor fed from a 220 Volt DC source is 5 ohms and the resistance of the excitation winding is R ohm and it rotates stably. Then, a resistance of R ohm is added to the excitation circuit (a resistor with the same value as the winding resistance) to control the speed. How many RPM is the motor in the last state in steady state.Mechanical losses will be neglected, motor magnetically linear, no saturation, temperature change will be neglected.Armature current = Ia = 4 ALoad torque=Tload= 7 Nm
A synchronous machine is a three-phase, two-pole machine with 36 stator slots and 5/6 full-pitched balanced armature windings. Each phase winding is made up of eight identical coils connected in sequence. Balanced three-phase 66 Hz currents with a peak amplitude of 16 A are used to drive the stator phases. a) What is the basic stator space mmf's maximum amplitude? (A.turns) b) How fast does the fundamental stator space mmf rotate mechanically? (rpm) c) What is the third-harmonic stator space mmf's maximum amplitude? (A.turns) d) What is the fifth-harmonic stator space mmf's maximum amplitude? (A.turns) e) How fast does the fifth-harmonic stator space mmf rotate mechanically? (rpm)