A cylindrical pressure tank with an outside diameter of 100 mm and a wall thickness of 5 mm is subjected to 40 kN load applied at d = 40 mm from the centerline. Determine the maximum internal pressure if the vertical normal stress in the tank is limited to 30 MPa. (MPa) Cross-Section Property: I₁ = 1₂ = () [dî – dî] X 40 kN 500 mm 40 kN

A cylindrical pressure tank with an outside diameter of 100 mm and a wall thickness of 5 mm is subjected to 40 kN load applied at d = 40 mm from the centerline. Determine the maximum internal pressure if the vertical normal stress in the tank is limited to 30 MPa. (MPa) Cross-Section Property: I₁ = 1₂ = () [dî – dî] X 40 kN 500 mm 40 kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

8000 mm3 aluminium cube is stressed in 3 mutually perpendicular direction x,y and z. The stresses in these directions are σx = 50 kPaσy = 80 kPaσz = -100 kPaDetermine the volumetric strain and change in volume. ν is 0.34 and E is 71 GPa
Find the maximum compressive and tensile normal stresses in the section given in the figure. Draw the graph of the neutral axis and normal stress next to the section. Find the normal stresses in kg / cm2. P =16964 KG EX=20 cm EY=6 cm
In the figure below, a member is subjected to an axial force P. If the cross sectional area of the member is denoted as AB, then the maximum value of its shear stress occurs when: ∅ = 00 ∅ = 300 ∅ = 450 ∅ =900
A thick cylinder of 0.5 m external diameter and 0.4 m internal diameter is subjected simultaneously to internal and external pressures. If the internal pressure is 25 MN/m2 and the hoop stress at the inside of the cylinder is 45 MN/m2 (tensile), determine the intensity of the external pressure,
The storage capacity of a thin cylindrical pressure vessel is 0.028 m³. The cylinder is subjected to an internal pressure of 21 MPa. The length of the cylinder is twice its internal diameter. Determine all the dimensions of the cylinder, if (a) the longitudinal stress does not exceed 160 MPa; and (b) the circumferential stress does not exceed 235 Mpa.
Determine the change in the volume of a 10 cm diameter copper sphere that is subjected to a hydrostatic pressure of 120 MPa assuming linear elastic behavior up to this stress level. (V =4/3 n 13) (E: 125 GPa, v = 0.34, SY = 200 MPa)
The 1900-NN load is applied along the centroidal axis of the member. (Figure 1) Determine the magnitude of the resultant internal normal force in the member section a-a. Express your answer to three significant figures and include the appropriate units. 2) Determine the magnitude of the resultant internal shear force in the member section a-a. Express your answer to three significant figures and include the appropriate units.
Complete all parts for upvote
n the figure below, a member is subjected to an axial force P. If the cross sectional area of the member is denoted as AB, then the maximum value of its normal stress occurs when: ∅ = 00 ∅ = 300 ∅ = 450 ∅ =900
The figure below are cables ( circular section) supporting a 48 kN. Find the axial stress of each. The cables has a limited working stress of 79 mPa. What will be the required diameter of each cables to support the 48 kN load? MN kN = 48 kN
The frame supports the distributed load shown with a maximum intensity of wo = 2 kN/m. Determine the state of stress acting at point E. (Figure 1) Figure Wo D• -1.5 m-+-1.5 m+ -3m- 3 m 20 mm 60 mm 20 mm m T D E 50 mm Part A Determine the normal stress at point E. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. σE= Part B μA TE= Value Determine the shear stress at point E. Express your answer to three significant figures and include the appropriate units. ΜΑ Units Value Units ? www ?
A 30 mm square is drawn on the rim of a large steel pressure vessel. The biaxial stress situation in the square after the pressure is applied is as shown in the figure. Determine the change in length of the BC edge in (mm).