A cylindrical cold storage facility with an inner diameter of 4m and height of 2m is constructed. For the wall, the first layer is 6 cm of glass wool (0.1 W/m-C), followed by 30 cm of concrete. The temperature inside is maintained at -10C (hin = 55 W/m^2-C) while the outside temperature is 10°C (hout = 22 w/m^2-C). If the steady rate of heat transfer is at 60W, (a) what is the thermal conductivity of concrete? (b) At what radius is the temperature at 0°C? To prevent water condensation inside the concrete wall (which damages the structure), A 5 cm layer of insulation (k = 0.15 W/m-C) is added to the exterior of the facility. (c) What is the new rate of heat transfer? (d) What is the temperature at the interface of the concrete wall and new insulation? (e) is condensation within the core of the wall prevented?

A cylindrical cold storage facility with an inner diameter of 4m and height of 2m is constructed. For the wall, the first layer is 6 cm of glass wool (0.1 W/m-C), followed by 30 cm of concrete. The temperature inside is maintained at -10C (hin = 55 W/m^2-C) while the outside temperature is 10°C (hout = 22 w/m^2-C). If the steady rate of heat transfer is at 60W, (a) what is the thermal conductivity of concrete? (b) At what radius is the temperature at 0°C? To prevent water condensation inside the concrete wall (which damages the structure), A 5 cm layer of insulation (k = 0.15 W/m-C) is added to the exterior of the facility. (c) What is the new rate of heat transfer? (d) What is the temperature at the interface of the concrete wall and new insulation? (e) is condensation within the core of the wall prevented?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What is the temparature at depth 1 cm from the surface at t=2 minutes after the start of the coolıng ?
Answer this ASAP,thx An empty sphere is made of aluminum (k = 202 W/m. °C) with an inner diameter of 4 cm and an outer diameter of 8 cm. The inside temperature is 100°C and If the ball above is coated with an insulating material having k = 50 mW/m. °C 1 cm thick. The outside of this insulation is in contact with an environment having h = 20 W/m.°C and Ts = 10°C, calculate the heat transfer under these conditions.
Find the heat transfer per unit area through the composite wall in the figure. Assume one-dimensional heat flow and there is no heat flow between B and C. The thermal conductivities are kA = 0.04 W/m/ºC, kB = 0.1 W/m/°C kc = 0.03 W/m/ºC, and kp = 0.06 W/m/°C. q T=370°C A B Area 0.1 m² Ꭰ -T= 66°C C 2.5cm → 7.5cm 5cm
3 Brass cube "p = 8530 kg/m , c= side length =9 mm, are annealed by heating them first to 813°C in a furnace and then allowing them to cool slowly to 130°C in ambient air at 28°C. If the average heat transfer coefficient is 19.9 W/m .°C, If 2204 balls are to be annealed per hour, what is the total rate of heat transfer (watts) from the balls to the ambient air? 380 J/kg.°C, k = 110 W/m.°C, a = 33.9E-6 W/m.°C",
Steaks (2 cm thick, k = 0.45 W/m - °C, « = 0.91 x 107 m2/s) usually have an original temperature of 25 °C. They will be cooled in a refrigeration room. The said room has a temperature of -11 °C. The heat transfer coefficient on both sides of the steak is 9 W/m2 - °C. How long will it take for both surfaces of the meat to be cooled to 2 °C? Assume the geometry of steaks to be a flat slab.
An insulated vertical cylindrical vessel of cross- sectional area A = 0.12 m² contains 20 mol of He gas at To = 300 K and Po= 0.5 bar. It is capped by a movable piston of mass m = 150 kg supported from the ceiling by a wire. The top of the vessel is open to the atmosphere (Patm= 1 bar, Tatm= 300K). The wire is cut and the weight falls and com- presses the gas. Patm 160 E Wir og SLOWA He gas 1019 (a) Obtain the pressure and temperature of the gas a short time after the wire has been cut, when a negligible amount of heat transfer has taken place. Comment on whether your solution takes into account the inevitable oscillations of the piston around its equilibrium position before it comes to rest. mut Ispl (b) After a long time, the He gas thermally equilibrates with the environ- ment by heat transfer through the piston. How much heat is exchanged with the environment during this process? Helium can be considered an ideal gas at all conditions of interest, with C₁=3R/2. INST
A house has a three meter deep basement (foundation) wall that is in a 10 meter by eight meter rectangular shape based on interior dimensions. On average, 2.5 meters of the wall is below grade. Assume the outside air temperature is 38°C and the inside temperature is 20°C; there is an average ground temperature of 27°C. Determine the rate of heat loss through the wall if it is insulated with an R-value of about 30°C.m^2/W.
A house has a composite wall of wood, fiberglass insulation and plaster board, as indicated in Figure 2.1. The total wall surface area is 300 m²" h = 30 W/m°K Tni = 20°C | h. = 60 W/m²K Teo =-15°C Fiberglass L=10 cm Plaster board k= 0.04 W/mK L=1 cm k = 0.15 W/mK Plywood L-2 cm k= 0.13 W/mK Figure 2.1 (i) Represent the composite wall by a thermal circuit, and label all the components in the circuit ii) Determine the inner surface temperature of the house.
3-52 A 4-m-high and 6-m-wide wall consists of a long 18-cm X 30-cm cross section of horizontal bricks (k = 0.72 W/m . °C) separated by 3-cm-thick plaster layers (k = 0.22 W/m . °C). There are also 2-cm-thick plaster layers on each side of the wall, and a 2-cm-thick rigid foam (k = 0.026 W/m - °C) on the inner side of the wall. The indoor and the outdoor temperatures are 22°C and −4°C, and the convec- tion heat transfer coefficients on the inner and the outer sides are h₁ = 10 W/m² . °℃ and h₂ = 20 W/m². °C, respectively. Assuming one-dimensional heat transfer and disregarding radi- ation, determine the rate of heat transfer through the wall. Foam Plaster Brick 1+₂+18 2 FIGURE P3-52 18 cm N 1.5 cm 30 cm 1.5 cm
solve a to c