A cylindrical caisson having an outside diameter of 9 m floats in sea water with its axis vertical and its lower end submerged 9 m, below the water surface. If its center of gravity is on the vertical axis and is 3.6 m above the bottom. a. Determine the value of ??? b. Find the true metacentric height. c. Find the righting couple when the caisson is tipped through an angle of 8°

Q: Calculate the uplift pressure at point C₂ shown in the figure below using Khosla's theory. 5m AH-6m…

A: Given Data: The data for the point C2 is given as: b=20md=3m

Q: Q3. Consider a buoy attached to a supporting cable as shown. The buoy is 3 m long, it has a diameter…

A: The length of the Buoy is l=3 m. The diameter of the Buoy is d=0.2 m. The specific gravity of the…

Q: The buoy is made from two homogeneous solid shapes each having a radius of 1.5 ft. The bottom is a…

A:

Q: Simply-supported beams with overhangs 10 m 40 kNm B +4 10 m 800 R q=5 kN/m 8 m D

A:

Q: Which of the following is a symmetric beam? 60 kN 60 kN а. В 2 m 2 m - 2 m b. A 2m 2m 4m B 20 kN/m…

A: Symmetric beam amoung the above given figure

Q: 3. Determine the reaction of supports using slope deflection method. El is constant. A 20 kN/m 6 m…

A: Given Data  Find support reaction using slope deflection method.

Q: For the built-up tee-shape (Ex= 350 MPa) shown: a). determine the yield moment My with respect to…

A:

Q: Calculate the maximum Vu and Mu in the beam shown below: 2m P(D)=20 KN P(L)=10 KN 4m 3. B

A: Given,  Simply supported beam with point load    To find : Maximum Shear force (Vu) and maximum…

Q: The measured length of an inclined distance was recorded to be 417.698 m long.  The difference in…

A:

Q: Q3: For the cantilever shown below, use the conjugate beam method to determine the displacement at…

A: Bending moment calculation:

Q: The measured length of an inclined distance was recorded to be 417.698 m long.  The difference in…

A:

Q: 4. A cylinder 8l 4.5 nas a height of 2.5 metres. Find the meta-centric height of the cylinder when…

A: option a is correct

Q: torque diagram,

A:

Q: A solid shaft has a circular cross section of diameter 150 mm and is required to transmit power at…

A: Given data : Diameter of shaft (d)=150 mm Angular speed n=9060 rps Maximum shear stress ζMax=85…

Q: Dima pulls directly backward with a force F 137N on the end of a 2.00 m-long oar. The oar pivots…

A: According to the question a girl dima pulls directly backwards with some force on of oar.The oar…

Q: :In Figure below, find the hydrostatic force on the curve AB Oil S=0.9 Tank Cylinder r=1.5m B 2.25 m…

A:

Q: A solid cylindrical pine (S = 0.50) spar buoy has a cylindrical lead (S = 11.3) weight attached, as…

A:

Q: 1. Calculate the design moment capacity þMn of the beam if fc 28 MPa and fy = 420 MPa 2. Check…

A:

Q: a) Determine the hydrostatic force (in kips) acting on the dam. b) Determine the moment of inertia…

A: We will solve this question in step no. 2

Q: Beam #2: Using Double Integration Method, Determine the Deflection at x = 1.0m (from left) and also…

A: ASKED: To determine the deflection of the beam given location and the maximum deflection.   Given,…

Q: For the beam shown, determine the following: a. Rotation at C in degrees. b. Rotation at F in…

A:

Q: A 5 kN -1.5 m- B ood -1.5 m D 2m

A:

Q: 10 kN 2 kN/m of I 6m- I 4m- 4m-

A:

Q: The distance between center of gravity and center of pressure on a submerged gate is decreasing as…

A: step 1-

Q: Determine the vertical displacement of Point EI is Constant. 10 KN C. 6 kN/m A & 3m к Use E = 2E8…

A: The problem can be conveniently solved using Superposition principle. By superimposing the…

Q: A wooden block (40 cm wide (b), 20 cm long (h) and 15 cm deep) floats on the seawater (specific…

A:

Q: 7. The tank indicated in the cross section 6 m long normal to the paper. The curved panel MN is one…

A: Note: As per bartleby guidelines we are allowed to do only first question of given multiple…

Q: Current Attempt in Progress The cantilever beam consists of a rectangular structural steel tube…

A:

Q: A bathy sphere is a spherical steel vessel for use in undersea observation and suspended by a cable…

A:

Q: Given the dimensions in the figure, one end of the beam is simple and the other end is fixed…

A: In this question, we first need to calculate the support reaction using the equilibrium equations…

Q: Using Superposition Method only, solve the following and show your complete solution: 1. Reaction at…

A: Given: Required : Reaction at A  Reaction at B Deflection at midspan

Q: SLOPE

A:

Q: Tank filles with water as shown in fig. fing the hevi Zental and vertical hydrostatic Force on the…

A: Given : - Tank filled with water  Cylinder radius (R) = 0.5 m  G = 15 KPa Height (H) = 3.5 m  Width…

Q: Using Conjugate-Beam Method. Consider 250 mm x 350 mm section and E = 200 GPa. Show complete and…

A:

Q: Determine the magnitude of the force on the pin at A for the jib crane shown. The beam AB is a…

A:

Q: 4. Rigid bar BEF is loaded, moving point F downward by 3mm. If the axial strain in bar DE is 400μ,…

A:

Q: Item 2: Solve the midspan deflection. 5W (kN/m) Im 2m 2m 8W (kNm) Э. 2m

A: The double integration method will be used for solving the mid span deflection of the given…

Q: The buoy is made from two homogeneous cones each having a radius of 1.5 ft. If h = 1.2 ft, find the…

A: The given figure is shown below:

Q: View Policies Current Attempt in Progress A solid cylindrical pine (S = 0.50) spar buoy has a…

A:

Q: Replace the force and couple moment system acting on the beam shown by an equivalent resultant…

A: The given figure is shown below

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.