A cylindrical caisson having an outside diameter of 7m floats in sea water sg=1.03 with its axis vertical and its lower end submerged 6m below the water surface. If its center of gravity is on the vertical axis and is 3m above the sea water surface. a. Determine the value of MBO, in meters b.Find the true metacentric height in meters is the caisson stable? c. find the restoring or upsetting couple, in kN-m, when the caisson is tipped through an angle of 9degree.

A cylindrical caisson having an outside diameter of 7m floats in sea water sg=1.03 with its axis vertical and its lower end submerged 6m below the water surface. If its center of gravity is on the vertical axis and is 3m above the sea water surface. a. Determine the value of MBO, in meters b.Find the true metacentric height in meters is the caisson stable? c. find the restoring or upsetting couple, in kN-m, when the caisson is tipped through an angle of 9degree.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solve all support reactions using the SLOPE-DEFLECTION METHOD. 210 kN A 8 m- I B 40 kN/m 8 m -21 E = constant D 4m-4m- C HOD OF SOAP $4411
Determine the maximum bending and shearing stresses developed in the beam 5. Ans.: (o)max = 149.45 MN/m? (O)max = 290.1 MN/m? (t)max = 5.77 MN/m2 %3D 10 kNim 200mm 20 kN.m B 2m A 4m 50mm Beam cross-section
A HOLLOW SHAFT D. = 2D, WHERE D. AND D₁ ARE THE OUTER AND INNER DIAMETERS RESPECTIVELY NEEDS TO TRANSMIT 20KW POWER AT 3000 RPM. IF THE MAXIMUM PERMISSIBLE SHEAR STRESS IS 30 MPA, FIND THE VALUE OF Do.
A simply supported beam column of 4 cm × 6 cm cross-section, 1.5 m long is subjected to an axial load of 8 kN in addition to a transverse concentrated load of 15 kN at a distance of 50 cm from one end. Determine the maximum deflection and the maximum stress in the column. Take E = 200 GPa
Find the minimum value of P which will make it: a.) Slipb.) Tip Over
In the propped beam shown, Solve for the following 1. wall moment 2. maximum deflection 10 kN/m IM TITTEN 2m 2m 12kN/m 1M
The 12 kN crate is being pulled by the force P as shown in the figure. The force P makes an angle of e with the horizontal. a) Find the smallest possible force P to cause the crate to slide. b) Determine the angle e. c) Determine the horizontal frictional force acting at the bottom of the crate, W=12KN Note : The total surface R I Pmin - M= 0.20
A wooden beam 150mm wide by 300mm deep is loaded as shown. If the maximhm flexural stress is 8MN/m^2. Find the maximum values of1.)W(kN/m)2.) P (kN)
Solve for the reactions on the given beam below using Slope Deflection Method
Problem # 1: A hollow shaft has an outside diameter 60 mm and a wall thickness of 1.25 mm. The maximum shear stress in the shaft must be limited to 150 MPa. Use G = 43 000 MPa. Determine: (a) the maximum power that can be transmitted by the shaft if the rotation speed must be limited to 20 Hz. (b) the magnitude of the angle of twist in a 700-mm length of the shaft when 30 kW is being transmitted at 8 rpm.