A closed traverse has the following data. Find the length and bearing of side EA

Q: E = 150GPa and I = 70 x 10^6 mm^4. Solve the slope at 5m from 6 kN/m 3 kN/m A BC tit 3m -0.000416rad…

A:

Q: If the fore bearing of a line is N 26°35' W, its back bearing will be

A: Back bearing is the bearing measured of any line in survey in opposite direction. For example…

Q: Solve 1 simple problem of Horizontal Alignment. Explain the Solution

A: Superelevation is generally the transverse slope that creates to get the effect of centrifugal force…

Q: 2.8m D B A 1.6m 2.4m 12KN 90° F 1.6m dla J 90° 12KN 1.6m 2.4m Determine the nature of forces CD, CF…

A: Given datatruss is given with loadingHinge at B and roller support at AFINDnature of forces in CD,…

Q: The dynamic viscosity of an \1 oil used for lubrication between a shaft and sleeve is 6 poise. The…

A: Solution: The correct option of the given question is Less than 200 W

Q: the distance of the shear center from the center of the bigger

A: option d Explanation is given below

Q: Given the cross-section notes of an earthwork betweèn station 10+100 to 10+200. Assume both stations…

A: Considering the following diagram:

Q: 20⁰ 30, A 6kN 2kN 0.4m 0.6m

A: Given:- To find:- Force in AB

Q: Compute the (Bearing, back azimuth, and back bearing) When the directions of AB= 143 15 and BC=228…

A:

Q: The following are the true bearings of a closed traverse. Compute the interior angles of each side.…

A:

Q: 1) For the given section shown: a) determine the area of the shaded portion ABCD; b) determine the…

A:

Q: Draw the 1ft contour lines across the 2-lane road below (12ft wide in each direction). (a) has a 4%…

A: a) Longitudenal slope= 4%crown-6 inchb)  Longitudenal slope= 6%cross slope=3%…

Q: 2a. Determine the location of the centroid of the built-up section measured from the top. 2b.…

A:

Q: Find redundant NBD.

A: ##CALCULATE Of forces in Redundant member BD##

Q: (a) (b) S-diagram A C (c) M - diagram 21.39 3m 25 kN G B 1.5m 1.5m F 5 kN/m E 18.61 3m C 0.5m 20 kNm…

A: Given Load 25 kN & 5 kN/mMoment 20 kNmSpan 11 mTo find out SFDBMD

Q: 2. Determine the Shear and Moment Diagram by Using Area Method. (Write the Degree of the Line/Curve…

A: Solution: Considering the diagram: Applying equilibrium…

Q: Determine the slope at C.

A: GIVEN :   P = 110.5 KN   L = 6 m TO FIND :    SLOPE AT  C ( θc )

Q: simple problem of Vertical Alignment. Explain the Solution

A:

Q: The whole circle bearing of a line is 287 degrees 15'. Find the reduced bearing of the line ?

A: Given. Whole circle bearing of a line is 2870 15'.Find the reduced bearing of the line ?Where,…

Q: A pipe is laid on a slope of 0.0002 and is to 3m³/s carry when the pipe flows at 70% of full depth.…

A:

Q: Degree of static indeterminacy

A: Given data : The value of number of member in truss=3 The value of number of joint in truss=4 The…

Q: e. Right 4.5 +1.0 Right 6.9 +2.6 side slope of both sections value of x at station 10+250 if it has…

A: solution of above problem is below:

Q: Contour lines never intersect each other. O a. TRUE b. Only true if there is an overhang clif O c.…

A: Contour is an imaginary line joining the point of equal elevation on the earth surface.

Q: Point P which is in the inner portion of the closed traverse ABCD, Solve for area with the given…

A:

Q: compute the azimuth and bearing of the remaining lines. Draw the figure

A: ###Computation of Azimuth and Bearing of the remaining lines####

Q: An open traverse that runs from A to G has the following deflection angles : B = 52deg 25’ L ; C =…

A: Diagram

Q: Find the bearing of the line having: dep= 434m and latitude of 650m

A: departure D=Lsinθ=434 m latitude L=Lcosθ=650m

Q: 4. Solve the Open ended Traverse below for the bearing at course EF: 250 A 42° Is' S87° 15'E 65 B F…

A:

Q: If whole circle bearing of a line is 120 °, its reduced bearing is A S 20°E B S 60° E CN 120° E D N…

A: Given- Whole circle bearing- WCB=120o, It is needed to find the value of reduced bearing.

Q: pearing of S 36° 42' 58", determine the ar

A:

Q: The reduced bearing of 20 m long line is S30° E the latitude of the line is A 17.32 m north B 10 m…

A: Given;Length = 20 mAngle () = S30E

Q: Explain correction for slope in chaining? Draw neat figures where necessary.

A: Concept introduction- Chaining- It is the process of measuring the distances in a linear way. It can…

Q: Draw the 1ft contour lines across the 2-lane road with 12ft lanes and 5ft wide shoulders. The…

A: Longitudenal slope= 5%cross slope=3% accross pavement                      =3% accross…

Q: It was known that the side BC of the closed traverse is twice as long as that of side CD. Find the…

A:

Q: (Trilateration): In a trilateration network one of the triangles has the following data: AB = 400m…

A:

Q: or the given truss system shown, determine ne following. Pi = 8kN and P2 = 12kN %3D F E 2 m B D 1 m-…

A: To find force in member FB ,EB

Traverse Survey

Traverse surveying is a popular method of surveying. Traversing is that type of survey where several connected survey lines form a framework and the directions and lengths of the survey lines are measured with the help of a tool to measure angles and tape or chain respectively. Traverse networks involve placing survey stations in a queue or trail and using pre-tested points as a basis for looking at the next point. This type of surveying is different from Tacheometric surveying, where only angles are measured and the process of chaining is reduced.