A cantilever beam made of wood spans L = 5 ft. The beam has a rectangular cross section with a width w = 7 in. and a depth d = 18 in. The moment of inertia of the cross section about the horizontal centroidal axis is 3402 in.4. A concentrated load P will be applied to the free end of the cantilever beam. Calculate the maximum magnitude that may be permitted for concentrated load Pif the allowable shearing stress for the wood is 110 psi. Answer: Pmax= Ib Save for Later Attempts: 0 of 1 used Submit Answer

A cantilever beam made of wood spans L = 5 ft. The beam has a rectangular cross section with a width w = 7 in. and a depth d = 18 in. The moment of inertia of the cross section about the horizontal centroidal axis is 3402 in.4. A concentrated load P will be applied to the free end of the cantilever beam. Calculate the maximum magnitude that may be permitted for concentrated load Pif the allowable shearing stress for the wood is 110 psi. Answer: Pmax= Ib Save for Later Attempts: 0 of 1 used Submit Answer

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

PROVIDE A CLEAR, COMPLETE, AND CORRECT SOLUTION AND FINAL ANSWER
W=10kN/m P=20.50
View Policies Current Attempt in Progress A simply supported wood beam that is 13.5 m long carries a 31 kN concentrated load at B. The cross-sectional dimensions of the beam are b = 150 mm, d = 430 mm, a = 65 mm, and c = 20 mm. Section a-a is located at x = 2.3 m from B. (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At sectiona-a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entire span. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length. P a H. a В K L 2L 3. 3 Answer: КРа (a) TH = kPa (b) TK = kPa (c) Tmax MPa (d) Omax = Submit Answer Attempts: 0 of 3 used Sava for Late Using multiple attempts will impact your score, 56 score reduction after attempt 1
A beam with the cross-section shown is loaded in such a way that the maximum shear is 4.8 P kN and the maximum moments are 2.5 P kN-m and -3.6 kN+m, where is the applied load in kN. Determine the maximum safe value of P if the allowable shearing stress is 8MPa and the allowable bending stress are 30MPa in tension and 60MPa in compression.
The cross section of a wood beam carries a bending moment M of magnitude 20R lb.-in. acting at 100 to the horizontal. Determine(a)the angle between the neutral axis and the horizontal; and (b) the maximum bending stress acting on the cross section. Note: ( R=990)
The rigid beam ABC is supported by a pin connection at C and by steel rod (1), which has a diameter of 7 mm. If the normal stress in rod (1) must not exceed 215 MPa, what is the maximum uniformly distributed load w that may be applied to beam ABC? What is the allowable force in road (1)? Use dimensions of a = 350 mm, b = 700 mm, and c = 525.0 mm.
la. Draw the V and M Diagram 10kN/m 12KN/m 5kN/m 3kN-m 3m 2m 2m 3m 1b. Compute for the maximum bending stress of the given beam if the cross sectional area is: 30mm 30mm 60mm 1.c. Compute the flexural stress at 3m from the hinge if the cross sectional area is: Equilateral Triangle 100mm
The beam shown in figure carries a uniformly distributed load of w on overhang BC. The beam is constructed of a wood beam [E,=12 GPa] that is reinforced on its upper surface by a steel plate [E,-200 GPa] plate. Assume that the allowable bending stresses of the wood and the steel are o. = 9 MPa and o = 165 MPa, respectively. Determine the largest acceptable magnitude for distributed load w. [L = 4m, a = 1.25 m, b. =150 mm, d, =280 mm, b. = 230 mm, t, = 6 mm] IC
With FBD
A) Define the bending stress as relates of beams. B)A fixed AB length 3m carries a point load of 45KN at a distance of 2m from A.if the flexural rigity (i.e. EL)is 1×10^4KNm^2, determine: I) fixed end moment A and B II) Deflection under the load III) the maximum deflection IV) The position of the maximum deflection.
The steel beam has the cross-sectional area shown. If w = 5.2 kip/ft, determine the absolute maximum bending stress in the beam where: L1= 6 ft; L2 =9 ft; bf = 8.5 in; and tw 0.3 in %3D E L1 L2 L1 - C0.30 in. tw 10 in. :0.30 in.
3) Find the maximum shear stress. 4) Find the deflection midway between the supports. 4 kN/m 5 kN 1m 2 kN.m 2m 2m 2m 2m 5 mm E=200 GPA 20 mm 50 mm- Beam Cross-Section